{"title":"Coverstar","description":"\u003cp\u003eCoverstar pool equipment and replacement parts at Active Pool Supply.\u003c\/p\u003e","products":[{"product_id":"coverstar-a1100-ug-403-detachable-rope-set","title":"Coverstar A1100 Slider Assembly for Detachable Rope, 403 and 801A Under Guide","description":"\u003cp\u003eThe Coverstar A1100 is the genuine under track slider assembly for detachable rope sets on 403 and 801A under guide automatic pool cover systems. The slider is what the rope pulls along the track, and it takes the load on every open and close.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eMost Coverstar automatic covers, Pool Cover Specialists systems built from 2017 onward, and any cover that uses a 3-hole detachable rope tab. If your rope tab has three holes, this is the slider that mates with it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eReplace them as a pair\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOne slider runs in each track and they wear together. Fitting one new slider against one worn slider tends to pull the leading edge out of square, so order two.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRope is not included. Coverstar Powerflex rope with a semi-rigid tab is sold separately in 100, 120, 125 and 150 foot lengths, and is usually replaced at the same time.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48620698271956,"sku":"CVR-72-1100","price":75.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_17f27824-bbbb-48dc-8b3f-adb28c1bc97c.png?v=1788573181"},{"product_id":"coverstar-h1070-pulley-250-double-ball-bearing","title":"Coverstar H1070 Double Ball Bearing Rope Pulley, Stainless Steel","description":"\u003cp\u003eThe Coverstar H1070 is the standard .250 rope pulley for Coverstar automatic pool cover systems. It is stainless steel with double ball bearings, so the rope runs over it smoothly and the pulley holds up to years of daily open and close cycles in a wet, chlorinated environment.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the bearings matter\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA pulley that drags puts extra load on the rope and the motor every time the cover moves. Two ball bearings keep the sheave turning freely, which means less rope wear and a quieter, smoother cover.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the pulley only. If the end cap assembly or the Powerflex rope also needs replacing, those are separate parts.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624551330004,"sku":"CVR-721-4313","price":27.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_78ab4909-6136-41c0-9d8d-029dc741cbf0.png?v=1788642970"},{"product_id":"coverstar-c5120-120-foot-powerflex-rope-with-semi-rigid-tab","title":"Coverstar 120' Powerflex Rope with Semi-Rigid Tab","description":"\u003cp\u003eThe Coverstar C5120 is a 120 ft length of PowerFlex rope with a semi-rigid tab, the replacement rope for Coverstar pool cover systems.\u003c\/p\u003e\u003cp\u003eCover ropes fray and stretch with years of cycling. A worn rope lets the cover track unevenly and eventually snaps. Replacing it with the correct Coverstar rope keeps the system running as designed.\u003c\/p\u003e\u003cp\u003eConfirm the length you need before ordering. This is the 120 ft version.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624552968404,"sku":"VCR-721-C5120","price":165.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_65f83335-d8b8-4013-8cab-ab7300c5d7e1.jpg?v=1788643042"},{"product_id":"coverstar-c5100-100-powerflex-rope-with-semi-rigid-tab","title":"Coverstar 100 ft PowerFlex Rope with Semi-Rigid Tab","description":"\u003cp\u003eCoverstar C6100 is a 100 ft length of PowerFlex rope with a semi-rigid Keder tab, Coverstar tab 625, already fitted. It is the replacement rope for Coverstar covers that run a tabbed PowerFlex rope.\u003c\/p\u003e\u003cp\u003eThe same item has been listed as C5100. C6100 is the current Coverstar number; either reference points to this rope.\u003c\/p\u003e\u003cp\u003eBefore ordering, match the rope type and tab style to what is on your cover now, and confirm 100 ft is the length your system calls for.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624555262164,"sku":"CVR-721-5100","price":196.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_905bf7ce-4823-4420-8049-93335fe0df2c.jpg?v=1788643324"},{"product_id":"coverstar-e2000-115v-sealed-stainless-steel-standard-motor","title":"Coverstar E2000 115V Sealed Stainless Steel Motor","description":"\u003cp\u003eThe Coverstar E2000 is the standard motor for Coverstar automatic pool cover systems: a sealed, stainless steel, three wire motor running on 115V AC, manufactured by Bison. It is also known by the Coverstar number A1282.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSealed for the job\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn automatic cover motor lives in a housing that sees water, which is why this one is sealed and cased in stainless steel rather than a painted frame.\u003c\/p\u003e\u003cp\u003eThis is the genuine Coverstar replacement. Match the label on the motor you are removing to E2000 or A1282 before ordering.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624834085076,"sku":"CVR-721-2001","price":1998.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_1d6e20b7-c562-4658-aa69-c1eb91206af1.png?v=1788643252"},{"product_id":"coverstar-a1932-stainless-steel-lid-bracket","title":"Coverstar 13 in. Stainless Steel Adjustable Walk-on Lid Bracket with Mounting Base","description":"\u003cp\u003eThe Coverstar A1932 is a 13 in. adjustable walk-on lid bracket for automatic pool cover vaults. The mounting base and support arm are stainless steel, and it is rated for the full range of walk-on lid materials: aluminum, stone and concrete.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDesigned for the vault\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eExtra holes in the bracket stiffen it and give a bonding lug a place to attach; the lug itself is not included. The support arm is slotted so Coverstar lid extension kits bolt on for wider lids. Keep the lid to no more than 2 in. of overhang past the end of the arm so the load stays on the steel.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIn the box\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOne 13 in. lid top support arm plate, one mounting bracket and one bolt and screw set. If you only need to replace a damaged arm on an existing base, Coverstar sells the arm alone.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624873701588,"sku":"CVR-701-3032","price":194.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_3bc7f22a-6405-4c4c-bda9-39f9a5d88142.jpg?v=1788647959"},{"product_id":"coverstar-a0605-key-switch","title":"Coverstar Complete Control Switch Assembly","description":"\u003cp\u003eThe Coverstar A0605 is the complete lever control switch for Coverstar automatic pool cover systems. Push the lever up or down and the cover opens or closes. Behind the lever is a 3-wire Leviton extra heavy duty AC switch, chosen for reliable switching under the motor load, and the whole assembly runs on 110 V.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eKey lock door\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe access door over the lever locks with a key, so the cover can only be run by someone with the key. That is the safety feature that keeps children and guests from opening the cover, and it is why the switch is sold as a complete lockable assembly rather than a bare lever.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eLED indicator\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn LED on the switch lights whenever power is being supplied to the system, so a cover that will not move can be diagnosed at the switch first: no light means no power reaching it.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624877338836,"sku":"CVR-72-0605","price":224.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c0ff2393-19e5-431f-80a5-06587e3678a5.png?v=1788648524"},{"product_id":"coverstar-c5110-110-foot-powerflex-rope-with-semi-rigid-tab","title":"Coverstar 110' PowerFlex Rope with Semi-Rigid Tab","description":"\u003cp\u003eThe Coverstar C5110 is the PowerFlex rope in the 110 foot length, finished with a semi-rigid tab. It is the replacement rope for Coverstar automatic pool cover systems that call for this length and end style.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar offers the PowerFlex rope in more than one length, and this listing is the 110 foot version only. Measure the rope you are replacing, or confirm the length your cover system specifies, and compare the end of your existing rope with the semi-rigid tab shown here.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624880353492,"sku":"CVR-721-C5110","price":184.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_db79ed60-0b37-4806-a52d-70b2892057a3.jpg?v=1788648876"},{"product_id":"coverstar-a0996-guide-feed-with-hardware-for-403-801-series-under-guide-system-stainless-steel","title":"Coverstar Guide Feed with Hardware for 403\/801 Series Under Guide System, Stainless Steel","description":"\u003cp\u003eThe Coverstar A0996 is a stainless steel guide feed for 403 and 801 series under guide automatic cover systems, supplied with its mounting hardware. Its job is to guide the rope smoothly as the cover opens and closes so the rope cannot snag and damage the cover.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy stainless matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOther systems use plastic guide feeds, and those wear out quickly. Stainless steel lasts far longer, and a guide feed in good condition reduces the chance of the cover coming out of the guide and sinking to the bottom of the pool.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFor Coverstar under guide systems in the 403 and 801 series. The slider assembly, rope and pulley bearings for the same systems are separate parts.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624884908244,"sku":"CVR-72-4743","price":54.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b8097915-fae7-4ca6-85f1-74e635c8e565.png?v=1788649691"},{"product_id":"coverstar-a1153-slider-assembly-ug-retro-2-set","title":"Coverstar Slider Assembly, UG Retro, Set of 2","description":"\u003cp\u003eThe Coverstar A1153 is a retrofit under track rope slider assembly for automatic pool covers on the 403 and 801 guide systems with detachable ropes. It comes as a set of two.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe slider rides in the under guide track and carries the rope as the cover opens and closes. Because it moves every cycle, it is a normal wear item, and a worn slider shows up as a cover that binds, tracks unevenly or is hard on the rope.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the under guide (UG) retro version for detachable ropes. Confirm your cover uses the 403 or 801 guide system before ordering.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624938516692,"sku":"CVR-701-4620","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_18d2c367-7a69-4f4f-ae06-7973b04a50e5.png?v=1788655819"},{"product_id":"coverstar-a2570-low-voltage-touchscreen-controller","title":"Coverstar Touchscreen Pool Cover Controller","description":"\u003cp\u003eThe Coverstar A2570 is a low voltage touchscreen controller for automatic pool covers. It works with all Latham and Coverstar 3-wire motor systems, either driving the cover directly or through a compatible 121 Motor Controls or 3-Wire Limit control board.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eControl and monitoring\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe touchscreen opens and closes the cover and keeps a running count of cover cycles, which helps with planning service. Built in Latham Mesh links the controller wirelessly to multiple touchpads, so the cover can be operated from more than one location around the pool.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWi-Fi notifications\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConnect the controller to Wi-Fi and it sends a text or email each time the cover opens or closes. That is useful for a second home, a rental or any pool where you want to know the cover is shut.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRetrofit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe A2570 is retrofittable onto existing Latham and Coverstar systems, replacing the original switch or controller. Wiring and setup should follow the Coverstar installation instructions and be done by someone comfortable with low voltage control wiring.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48624968827092,"sku":"CVR-72-2464","price":628.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_37cef2b0-8be8-4547-afba-55c46679f0ea.png?v=1788656900"},{"product_id":"coverstar-a0041-single-cs1800-cs3000-eclipse-ug-3-leading-edge-white-block-insert-assy","title":"Coverstar Single CS1800\/CS3000\/Eclipse UG 3 in. Leading Edge White Block Insert Assembly","description":"\u003cp\u003eThe Coverstar A0041 is a single white block insert assembly for the 3 in. leading edge on CS1800, CS3000 and Eclipse underguide automatic cover systems. It is the factory part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis insert is specific to underguide (UG) track systems and to the 3 in. leading edge size. Confirm both before ordering, and check the part number A0041 against the parts breakdown for your cover.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eQuantity\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSold as one insert assembly. Order the number you need for the repair.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48625005986004,"sku":"CVR-72-4716","price":104.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b01fcc38-eca6-444b-b446-b31a136e2b33.jpg?v=1788661963"},{"product_id":"coverstar-a1071-guide-feed-2-piece-ss-tg-403","title":"Coverstar 2-Piece Stainless Steel Guide Feed Assembly without Mounting Hardware","description":"\u003cp\u003eThe Coverstar A1071 is a two piece stainless steel guide feed assembly for automatic pool cover systems. Coverstar lists it as working with all Top Guide Pre 801 setups and with the Pre 403 Under Guide system.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the guide feed does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe guide feed is the point where the cover rope enters the track. It has to hold alignment under load every time the cover runs, and it does that while sitting in splash and weather all year. When it wears or distorts, the rope stops feeding cleanly and the cover pulls crooked or binds partway across.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting and materials\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eStainless steel construction is the reason this part lasts in that position. The assembly is supplied in two pieces, which makes it easier to work around the rope already in place. Mounting hardware is not included, so keep the original fasteners or order them separately before you start.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48625745854676,"sku":"CVR-72-4742","price":60.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_601f9fbf-4962-452f-8fcc-bfe10cb432f3.jpg?v=1788690836"},{"product_id":"coverstar-c4062-tab-semi-rigid-for-detach-rope-418","title":"Coverstar Tab Semi Rigid for Detach Rope 418","description":"\u003cp\u003eThe Coverstar C4062 is the semi rigid tab used on detachable rope, supplied as the tab alone. It measures 3 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSemi rigid, and why that matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe tab has to keep its form so it can be pushed through and held, but still bend with the rope as the cover runs. Semi rigid is the middle ground the original part was built to, which is why a stiffer or softer substitute tends to fight the system.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe tab only. Rope, sliders and other cover hardware are separate items, so order what the repair actually needs.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48625750016212,"sku":"CVR-721-4062","price":14.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_3f02c87f-a9a9-4f21-9eee-ced669185c22.png?v=1788691778"},{"product_id":"coverstar-tp2500-touch-sensitive-touch-pad-full-assembly","title":"Pool Cover Specialists TP2500 Touch Sensitive Key Pad, Full Assembly","description":"\u003cp\u003eThe Pool Cover Specialists TP2500 is a wireless, touch sensitive key pad supplied as a full assembly, used to operate PCS automatic pool covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNo moving parts\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe buttons are touch sensitive rather than mechanical, and the body is sealed. That combination is what gives a control mounted outdoors a long life: there is no switch plunger to wear, no seam for water to work into and nothing to seize after a winter.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWireless, with access control\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe pad communicates with the cover system wirelessly, so installation is a matter of mounting and setting up the antenna rather than pulling a control cable. It arrives with a default access code and supports customized user settings, which is how you keep the cover from being operated by anyone who happens to walk up to the pad.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMounting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFit it within sight of the pool. An automatic cover should be watched through its full travel, and the pad belongs where whoever presses the button can see the water.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48625772560596,"sku":"CVR-701-TP2500","price":391.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_719d12ab-0abf-4227-9cf4-a3bba2332dd5.png?v=1788692069"},{"product_id":"coverstar-c5150-150-powerflex-rope-with-semi-rigid-tab","title":"Coverstar 150' Powerflex Rope with Semi Rigid Tab","description":"\u003cp\u003eThe Coverstar C5150 is a 150 ft length of Powerflex rope supplied with the semi rigid tab. It is the factory rope, ordered by part number.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuying by the length\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe rope comes as one 150 ft coil rather than cut to a set size, so it can be trimmed to the run your cover needs.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to change it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCover ropes wear where they pass through tracks and pulleys. A rope that is frayed, stiff or thinning at the wear points is replaced rather than repaired, since a rope that lets go mid cycle can leave the cover stranded.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48625852711124,"sku":"CVR-721-5150","price":202.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_3bfe1d92-7158-403a-a368-33368abe3dd8.jpg?v=1788701687"},{"product_id":"replacement-motor","title":"Coverstar 3-Wire Motor \u0026 Housing STD with CS1800 Mounting Brackets, A0610","description":"\u003cp\u003eCoverstar A0610 is a replacement motor supplied as a complete assembly: the 3 wire motor in its STD housing, with the CS1800 motor mounting bracket.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it replaces\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn automatic pool cover is driven by a motor at one end of the mechanism. When that motor fails, the cover either stops part way, hums without moving, or does nothing at all. Because this listing is the motor and housing as one unit, you are not stripping a failed motor out of an old housing to reuse it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore ordering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar builds this motor in more than one wiring configuration and more than one mounting arrangement. This is the 3 wire motor in the STD housing with the CS1800 bracket, so check the motor you are removing against that description. It is also worth ruling out the rope, the pulleys and the control switch first, since a worn drive can look exactly like a dead motor.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48625854185684,"sku":"CVR-72-1005","price":1440.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_13203696-ce40-4217-b151-c02532dbd08c.png?v=1788701749"},{"product_id":"coverstar-a0958-pulley-endcap-assembly-twist-lock-ut-817","title":"Coverstar Pulley Endcap Assembly, Twist Lock UT 817","description":"\u003cp\u003eCoverstar A0958 is the pulley endcap assembly in the twist lock UT 817 configuration, a service part for Coverstar automatic pool cover systems.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSold as an assembly\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe part comes as the complete pulley endcap assembly rather than a loose pulley, so the pieces arrive together in the configuration Coverstar built.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck the number\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar produces endcaps in more than one style, and they are not interchangeable. Read the part number on the piece coming off the system and confirm it is A0958 before ordering.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48626212339924,"sku":"CVR-721-4314","price":57.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_5c857397-5384-4039-8d60-38b0a61efd48.jpg?v=1788706213"},{"product_id":"coverstar-a2392-19-75-long-lid-bracket-extension-kit-23-25-stainless-steel","title":"Coverstar 19.75\" Long Lid Bracket Extension Kit, 23\" to 25\", Stainless Steel","description":"\u003cp\u003eThe Coverstar A2392 is a stainless steel lid bracket extension kit with 19.75 in. support arms, listed for the 23 in. to 25 in. size step. It extends the reach of an adjustable walk-on lid bracket so a wider vault lid stays properly carried.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it works with\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe extension arms are engineered to work with the 13 in. adjustable walk-on lid bracket with a stainless steel base, given in our source as Coverstar part A1932. They are meant to give solid support under stone and concrete lids, which is where an unsupported lid will crack or sag first.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMeasure before you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar states that the lid should not extend more than 2 inches beyond the length of the support arm. This kit is labeled for 23 in. to 25 in. while the arms measure 19.75 in., so take both numbers to your own vault and lid rather than assuming one from the other. Coverstar also makes matching kits in other arm lengths if this one does not line up.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy stainless\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe bracketry inside a cover vault sits in a wet, dirty, mostly ignored space. Stainless is what keeps the supports doing their job years after the vault was last opened.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48626218467540,"sku":"CVR-701-2392","price":296.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_df6dc2b6-f6ae-47f5-89b2-eb676fdbf727.jpg?v=1788706414"},{"product_id":"coverstar-a2365-17-75-stainless-steel-lid-bracket-21-23-extension-kit","title":"Coverstar 17.75\" Stainless Steel Lid Bracket 21-23\" Extension Kit","description":"\u003cp\u003eThe Coverstar A2365 is a stainless steel lid bracket extension kit with 17.75 in arms, built to take a walk-on lid bracket out to a 21 to 23 in lid.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it works with\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe extension arms are engineered to be compatible with the 13 in adjustable walk-on lid bracket that uses a stainless steel base, Coverstar part A1932. That bracket sets the mounting point, and this kit extends the reach so a wider lid can sit on it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuilt for heavy lids\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThese are support arms for stone and concrete lids, not for light covers. Stainless steel throughout suits a part that spends its life in a damp, buried cover box.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSizing the lid\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFor the arm to do its job, the lid should not extend more than 2 inches past the length of the support arm. Measure the lid before choosing an extension size, because a lid that runs too far past the end of the arm loses support exactly where it needs it.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48626261950676,"sku":"ASC-721-1021","price":118.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_e36ec528-98c7-4fd4-b344-eb366fd6363e.jpg?v=1788707461"},{"product_id":"coverstar-stop-block-slider-805-403","title":"Coverstar Stop Block Slider for Wheel Assembly 805, STD TG 403, M9886","description":"\u003cp\u003eThe Coverstar M9886 is the stop block slider for the 805 wheel assembly and the standard TG 403. It locks into the guide, which is how the stop position is held.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy it wears\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe slider takes the load every time the cover reaches the end of its travel, and it does that thousands of times over the life of a cover. When it is worn or gone, the assembly no longer stops where it should and the cover stops sitting square.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOrdering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is Coverstar part M9886, sold individually. How many you need depends on the track layout, so count what is fitted before you order.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48626282365140,"sku":"CVR-72-9886","price":20.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_58deb549-1afa-427d-9e95-94a9849c9ede.png?v=1788707614"},{"product_id":"cp-cover-guide-feed-u-g-ea","title":"Coverstar Guide Feed for Cover Pools Under Guide System","description":"\u003cp\u003eThe Coverstar RP1003 is the guide feed for the Cover Pools under guide system. It is sold individually.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe guide feed leads the edge of the cover into its track as the cover runs. It is a piece of hardware the cover passes over on every open and close, so it wears and is meant to be replaced.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to change it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eLook at the feed when the cover starts to catch, drag or run off line at the track entry. A feed that is cracked, grooved or missing altogether will not lead the edge cleanly, and the cover fabric pays for it.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48626389385428,"sku":"CVR-72-1300","price":91.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_d61911ef-c4a6-4025-a2da-9add7022f767.jpg?v=1788709684"},{"product_id":"coverstar-a3409-lid-bracket-with-bolt-for-419-zero-reveal-riser","title":"Coverstar Lid Bracket with Bolt for 419 Zero Reveal Riser","description":"\u003cp\u003eThe Coverstar A3409 is the lid bracket, supplied with its bolt, for the 419 Zero Reveal riser on a Coverstar automatic pool cover.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe bracket is the hardware that carries the lid over the cover mechanism. It takes the weight of the lid every time it is lifted and closed, and it sits outdoors through every season, so it is one of the pieces that eventually cracks or corrodes.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm the riser is the 419 Zero Reveal, and count how many brackets on your lid need replacing. This listing is a single bracket with its bolt.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48626478055636,"sku":"CVR-721-3409","price":119.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_532070aa-8558-4711-afab-68de8a83db71.jpg?v=1788710686"},{"product_id":"coverstar-lid-tray-walk-on-with-mesh-24in-x-23-75in-lip-side","title":"Coverstar Lid Tray Walk-On with Mesh, 24 in x 23-3\/4 in Lip Side","description":"\u003cp\u003eThe Coverstar A0229 is a walk-on lid tray with mesh, 24 inches by 23-3\/4 inches, for the lip side of an automatic pool cover housing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it goes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eLid trays span the top of the cover vault and close it off at deck level. The walk-on version is the one built to be stood on, so the vault becomes part of the walking surface around the pool instead of an area people have to step around.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eTrays are both sized and sided. Measure the opening on your housing, and confirm you need the lip side piece rather than its opposite, because the two are not interchangeable.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48626515050708,"sku":"PSU-155026","price":252.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c284cc71-d4ae-46a8-bb29-7779cb9b9d2f.jpg?v=1788711158"},{"product_id":"coverstar-c5080-80-foot-powerflex-rope-with-semi-rigid-tab","title":"Coverstar 80' PowerFlex Rope with Semi-Rigid Tab","description":"\u003cp\u003eThe Coverstar C5080 is an 80 foot length of PowerFlex rope with a semi rigid tab, the genuine Coverstar part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy rope gets replaced\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCover rope works every time the cover moves. It stretches, it abrades where it passes through guides, and eventually it frays. Long before it breaks it starts letting the cover run crooked or bind, which is usually the first sign an owner notices.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eGetting the length right\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis listing is the 80 foot rope. Measure what you are replacing before ordering, since Coverstar supplies this rope in set lengths and the tab is already fitted at the end.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627004178644,"sku":"CVR-721-C5080","price":101.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_7dd910f6-419a-48e0-8229-038eb68a330f.jpg?v=1788718957"},{"product_id":"coverstar-x0091-21-light-gray-encapsulation-track-shim-for-801-403-series-vinyl-liner-and-fiberglass-pool","title":"Coverstar 21' Light Gray Encapsulation Track Shim for 801\/403 Series","description":"\u003cp\u003eCoverstar X0091 is the light gray encapsulation track shim in a 21 foot length, listed for the 801 and 403 series on vinyl liner and fiberglass pools.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it belongs\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe shim is part of the encapsulation track system that carries an automatic cover, not a standalone accessory. It is ordered by series, length and color, and this one is the 21 foot light gray piece for the 801 and 403 series.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore ordering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm the series on your existing installation and the length you need, since the shim has to match the track it is going into.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627203080404,"sku":"CVR-72-1224","price":97.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_74c8c014-b941-4349-806a-0c5467788b68.png?v=1788720050"},{"product_id":"underguide-right-gear-assy","title":"Coverstar Gear Assembly CS1800, Deck Left, Recessed Right","description":"\u003cp\u003eThe Coverstar A2396 is a gear assembly for the CS1800 automatic pool cover system, supplied in the deck left, recessed right configuration. The same part is listed elsewhere in the Coverstar catalog as the underguide right gear assembly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn automatic cover moves on guides driven through gearing at each end. When the teeth in one of those assemblies wear or strip, the cover loses its smooth travel: it drags, makes noise, or stops short of closing. Swapping the assembly restores the drive.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm the handing. This part is described two ways in the source catalog, so match it against the parts breakdown for your CS1800 installation rather than ordering on the name alone.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627402866900,"sku":"CVR-72-2396","price":276.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_e58c596a-7246-4b9a-82f2-067e486e2798.jpg?v=1788723036"},{"product_id":"coverstar-a1157-12-walk-on-lid-bracket-arm","title":"Coverstar 12\" Walk On Lid Bracket Arm","description":"\u003cp\u003eThe Coverstar A1157 is the 12 inch walk on lid bracket arm, a replacement for the arm that supports the walk on lid over an automatic pool cover vault.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it holds up\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe walk on lid is the section of decking that covers the cover mechanism at the end of the pool. People stand on it. The bracket arms are what hold it level and carry that load, so a bent or corroded arm shows up as a lid that rocks, sits proud, or no longer feels solid underfoot.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOrdering the right one\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the arm by itself, at 12 inches. It is not a complete bracket assembly with a mounting base, and Coverstar builds the arm in more than one length. Pull the old arm, measure it, and match the length before ordering.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627627950292,"sku":"CVR-701-4675","price":93.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4efed04e-6169-41c1-bd04-bfd5214757c4.png?v=1788725549"},{"product_id":"coverstar-10-stainless-steel-adjustable-walk-on-lid-bracket-with-mounting-base","title":"Coverstar 10\" Stainless Steel Adjustable Walk-On Lid Bracket, Arm Only","description":"\u003cp\u003eThe Coverstar A0510 is the 10 inch adjustable walk-on lid bracket for an automatic pool cover vault. The base and support arm are stainless steel, which is the only sensible material for a part that sits in a wet, chemically loaded box in the deck.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it carries\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar list the bracket for a range of lid materials, including aluminum, stone and concrete. The holes through the bracket are placed to add rigidity as well as to give more than one way to mount it, and the same holes let an installer attach a bonding lug. The bonding lug is not supplied with the bracket.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSizing the lid\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar recommend the lid does not extend more than 2 inches past the end of the support arm. Past that, the unsupported overhang is what flexes and cracks under foot traffic.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOne note before you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis listing is titled arm only, while the Coverstar product description for the same bracket covers it with a mounting base. If you need the base as well as the arm, contact us and we will confirm what ships.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627634831572,"sku":"CVR-701-4670","price":110.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_225fc689-2aee-42e9-b8c7-a9c20a54d811.png?v=1788725693"},{"product_id":"torque-limiter-w-housing-only","title":"Coverstar Torque Limiter with Housing for CS1800 and CS3000 Electric Motors","description":"\u003cp\u003eThe Coverstar A0126 is the torque limiter for the CS1800 and CS3000 electric pool cover motors, supplied complete with its housing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is for\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn automatic cover can meet resistance at any point in its travel: ice, a leaf jam in the track, a rope that has wandered off the reel. The torque limiter sits in the drive line as the intended weak point. When load rises beyond its set point it slips, so the shock is absorbed there rather than by the motor or the cover mechanism.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore and after fitting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA limiter that has given up is usually reporting a problem somewhere else. Work the cover by hand, look for binding in the tracks and at the reel, and clear whatever caused the load before the new limiter goes in, or it will see the same treatment.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627728548052,"sku":"CVR-701-4760","price":94.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_3ac07eb3-ea0c-45ba-a27f-897de519fb7b.jpg?v=1788727367"},{"product_id":"lid-bracket-adj-base","title":"Coverstar Walk-On Lid Bracket Adjustable Base with 2 Mounting Slots, 8 Inch","description":"\u003cp\u003eThe Coverstar M9678 is the adjustable base for a walk-on lid bracket, listed at 8 inch with two mounting slots.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA walk-on lid covers the housing that holds an automatic pool cover, and it has to sit flush and take foot traffic. The bracketry underneath carries that load. This base is the adjustable half: it fixes down first, and the two slots let it be moved before the fixings are pulled tight, which is how the lid is brought level with the deck.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eMeasure the base you are replacing and confirm the 8 inch length and the slotted pattern match. Where one base has corroded or deformed, the neighboring bases along the same run are usually the same age and worth inspecting at the same time.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627729596628,"sku":"CVR-72-5330","price":98.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b30b9d5f-b751-4b07-a93d-61bed968e4d4.jpg?v=1788727388"},{"product_id":"coverstar-powerflex-detachable-rope-120-with-keder-tab-625","title":"Coverstar PowerFlex Detachable Rope 120' with Keder Tab 625","description":"\u003cp\u003eThe Coverstar C6120 is the PowerFlex detachable rope, supplied in a 120 foot length with Keder tab 625.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy rope gets replaced\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe rope carries the load every time the cover runs, and it wears steadily rather than failing all at once. Changing it on a schedule is cheaper and far less disruptive than dealing with it after it has let go mid cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOrdering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOrder by the part number, C6120, and confirm that 120 feet and the 625 Keder tab match what your system uses before ordering.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627742638292,"sku":"CVR-72-1058","price":251.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_298bbaea-d423-4410-bdcf-8fd2a6d57f2e.jpg?v=1788727612"},{"product_id":"coverstar-c3240-140-foot-powerflex-rope-with-semi-rigid-tab","title":"Coverstar 140' PowerFlex Rope with Semi-Rigid Tab","description":"\u003cp\u003eThis is the Coverstar PowerFlex detachable rope in a 140 foot length, supplied with a semi-rigid tab and the 518 silver tracer. It is listed under part number C5140 and also appears as C3240.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn automatic pool cover is drawn back and forth by rope running through the track, and that rope is a wear part. It takes constant tension, abrasion in the track and the full weight of a wet cover, so it stretches and frays long before the rest of the system needs attention.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMatching your system\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eLength and tracer both matter. This one is 140 feet with the 518 silver tracer, and it comes with the semi-rigid tab fitted rather than as plain rope. If you are replacing one side of a pair, measure what came off and check the tracer on the old rope before ordering.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627765444820,"sku":"CVR-721-3240","price":112.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_69e3520d-2c1a-4aa0-95cb-a01eb9914a6c.jpg?v=1788727842"},{"product_id":"coverstar-leading-edge-insert-caps-for-2-1-2-le-set","title":"Coverstar Leading Edge Insert and Caps for 2-1\/2\" Leading Edge (LE) Set","description":"\u003cp\u003eThe Coverstar A1678 is the genuine OEM leading edge insert with caps for a 2-1\/2 inch aluminum leading edge, supplied as a set of 2. It is for Coverstar automatic pool covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the leading edge does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe leading edge is the aluminum bar at the front of the cover, the piece that travels the length of the pool and carries the fabric with it. The insert and its caps are what let that bar hold together and take the load every time the cover runs.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck the size first\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar builds leading edges in more than one size. This set is for the 2-1\/2 inch bar, and the 3 inch bar takes a different insert assembly, so measure the existing edge before ordering. Fitting the wrong insert wastes a trip and leaves the cover down.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627851067604,"sku":"CVR-721-1678","price":236.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_ccb46d80-6401-4f39-80ae-21a4de864061.jpg?v=1788728290"},{"product_id":"coverstar-a1931-base-plate-bracket-for-13-adjustable-lid-bracket","title":"Coverstar A1931 Base Plate Bracket for 13\" Adjustable Lid Bracket","description":"\u003cp\u003eThe Coverstar A1931 is the genuine replacement base plate bracket for the 13 inch adjustable lid bracket used on Coverstar automatic pool cover lids.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it sits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe lid over a cover mechanism is carried on adjustable brackets. Each bracket has an arm that sets the height and a base plate that anchors it to the structure. This listing is the base plate, the fixed half of that pair, matched to the 13 inch adjustable arm.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm the bracket length on your lid. The 10 inch and 12 inch arms use their own hardware, so a base plate for the 13 inch bracket will not serve those. The adjustable arm itself is a separate part and is not included here.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627860963540,"sku":"CVR-701-A1931","price":77.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_e5153182-b049-4253-9ec9-6391e4473a13.jpg?v=1788728535"},{"product_id":"coverstar-c5090-90-foot-powerflex-rope-semi-rigid-tab","title":"Coverstar 90' PowerFlex Rope Semi-Rigid Tab","description":"\u003cp\u003eThe Coverstar C5090 is PowerFlex rope with a semi-rigid tab, supplied in a 90 foot length. It is a component of the Coverstar automatic pool cover system.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is for\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe rope is what the cover system pulls against, and the semi-rigid tab is the end fitting that ties it into the mechanism. Rope is a wear item on any automatic cover: it takes the load every time the cover opens and closes, and over seasons it stretches, chafes and eventually frays.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eMatch the C5090 part number and the 90 foot length against what is on your system. Coverstar builds several rope configurations, and the tab style is what distinguishes them.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48627977617620,"sku":"CVR-721-C5090","price":116.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_38eb8ca4-7ece-4b14-8b3f-19487ebc602d.jpg?v=1788732130"},{"product_id":"coverstar-c5130-130-foot-powerflex-rope-with-semi-rigid-tab","title":"Coverstar 130' Powerflex Rope with Semi-Rigid Tab","description":"\u003cp\u003eThe Coverstar C5130 is the Powerflex rope with a semi-rigid tab, supplied in a 130 foot length. It is the genuine Coverstar part for their automatic pool cover systems.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the rope does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOn an automatic cover, the rope is what actually pulls the cover across the pool and back. It runs through the tracks on every cycle, so it carries the load and the wear for the whole system. When it frays or stiffens, the cover starts to bind or stops partway.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe semi-rigid tab\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe tab comes fitted to the rope, which is the end that connects into the cover system. Buying the rope with the tab already on it saves fabricating the connection on site.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48628871037140,"sku":"CVR-721-C5130","price":252.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_0d5a538c-4e51-458c-a938-353c373650cb.jpg?v=1788756823"},{"product_id":"coverstar-a0797-tube-insert-with-screw-for-5-inch-tube","title":"Coverstar Tube Insert with Screw for 5 Inch Tube","description":"\u003cp\u003eThe Coverstar A0797 is a tube insert with screw for a 5 inch automatic pool cover tube. It is the genuine Coverstar part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe insert sits inside the end of the cover tube and gives the tube something solid to locate and turn on. When it wears, splits or works loose, the tube develops play at the end and the cover stops tracking the way it should. Replacing the insert is a far smaller job than dealing with the damage that comes from running a cover on a sloppy tube.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eInserts are size specific. Measure the tube diameter and confirm it is 5 inches, because an insert made for a different tube will not grip. The screw needed to secure the insert is included.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48629101363412,"sku":"CVR-72-0797","price":236.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_518a9e2b-cbca-4cd5-bce0-9a37f1b490d6.png?v=1788759701"},{"product_id":"coverstar-c5125-125-powerflex-rope-with-semi-rigid-tab","title":"Coverstar C5125 125 ft Powerflex Rope with Semi-Rigid Tab","description":"\u003cp\u003eThe Coverstar C5125 is a 125 foot length of Powerflex rope with a semi-rigid tab already fitted. It is the genuine Coverstar part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it goes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRope is what actually pulls an automatic pool cover open and closed, and it works every time the cover cycles. That constant loading is why rope is treated as a service item rather than a permanent part of the system.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eMeasure the run your cover needs so you know how much of the 125 feet you will use. If you are unsure which rope your system takes, check the part number on what is currently installed.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48629140783316,"sku":"CVR-721-5125","price":174.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b841460f-2a10-4b43-b2ec-23b00a31b7b7.jpg?v=1788759968"},{"product_id":"coverstar-a2364-coverstar-13-75-stainless-steel-lid-bracket-17-19-extension-kit","title":"Coverstar 13.75\" Stainless Steel Lid Bracket 17-19\" Extension Kit","description":"\u003cp\u003eThe Coverstar A2364 is a stainless steel lid bracket extension kit covering the 17 to 19 inch range. It is the part that lets a walk-on lid bracket carry a wider lid over the cover vault.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it works with\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe arms are made to attach to the Coverstar adjustable walk-on lid bracket with the stainless steel base, part A1932. That bracket sets the lid height and the arms extend the span, so both pieces are needed for the assembly to work.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuilt for heavy lids\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eStone and concrete lids are what this kit is for. Stainless was chosen because the arms sit in a vault that stays wet, and because the load is real. Measure the opening before ordering, since the same kit is made in several ranges.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe overhang rule\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eKeep the lid within two inches of the end of the support arm. Anything more and the unsupported edge of the lid is carrying itself, which is the usual reason a stone lid cracks along a line rather than at a corner.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48629285552340,"sku":"CVR-701-A2364","price":47.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_924fca43-e054-456d-afc1-5344c70a148b.jpg?v=1788761931"},{"product_id":"torque-limiter-w-o-housing","title":"Coverstar Torque Limiter without Housing for CS1800 and CS3000","description":"\u003cp\u003eThe Coverstar A0108 is the complete torque limiter for the CS1800 and CS3000 electric motor automatic pool cover systems, supplied without the housing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA torque limiter sits between the motor and the drive. If the cover meets something it should not, a snagged edge, ice, a jammed track, the limiter gives way before the full load reaches the drive train. It is the part that turns an expensive failure into a nuisance.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe housing is not included. This listing suits a rebuild where the existing housing is still good, so inspect it before ordering. Everything else in the torque limiter is supplied complete.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48629304688852,"sku":"CVR-701-4755","price":239.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_aa37787e-1b05-4af3-99f5-ab0f079e7885.jpg?v=1788762150"},{"product_id":"coverstar-c6080-powerflex-rope-80-keder-tab-625","title":"Coverstar C6080 PowerFlex Rope 80 Keder Tab 625","description":"\u003cp\u003eCoverstar C6080 is the PowerFlex Rope 80 Keder Tab 625, a service component for Coverstar pool cover systems.\u003c\/p\u003e\u003cp\u003eCover hardware is ordered by number rather than by description. Tabs and rope in this range look similar across builds and are not freely interchangeable, so confirm C6080 against your cover paperwork, or against the part you are taking off, before ordering.\u003c\/p\u003e\u003cp\u003eIf you are not sure, the company that installed the cover will have the build details on file and can confirm the number in a minute.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48629536063700,"sku":"CVR-72-1054","price":178.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_ee85c551-719e-4ac6-a80a-717c5858c9c3.png?v=1788766304"},{"product_id":"coverstar-a0020-non-motor-end-brake-assembly","title":"Coverstar Non-Motor End Brake Cone Assembly","description":"\u003cp\u003eThe Coverstar A0020 is the non-motor end brake assembly for CS1800 automatic pool cover systems. It arrives as the complete NME casting with the brake assembly, cone and square plate already together.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAlong with the casting you get the brake spring, the CS1800 NME brake block, a 1\/4 inch split lock washer, a 1\/4 inch stainless steel flat washer, a 1\/4 inch-#20 by 1 inch hex head bolt and a 1\/4 inch-#20 stainless steel nut. That is the full set of small parts the brake needs, so the job does not stall waiting on a washer.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it goes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe non-motor end is the far end of the cover mechanism from the drive motor. When the brake at that end wears or seizes, this assembly replaces it as one piece rather than as a handful of loose components.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48633449185492,"sku":"CVR-72-5300","price":300.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b5d443bb-ca3c-46eb-aa9d-8bb3ef155a82.jpg?v=1788804765"},{"product_id":"leading-edge-insert","title":"Coverstar Leading Edge Bar Insert Assembly Set","description":"\u003cp\u003eThe Coverstar A0439 is the leading edge bar insert assembly set for a Coverstar automatic pool cover. It is the genuine Coverstar part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it goes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe leading edge bar is the rigid bar sewn into the front of the cover fabric, the part that is pulled across the water and back again every time the cover is run. The inserts sit inside that bar. Because the whole assembly carries the load of the fabric on every cycle, insert hardware is a normal service item on an older cover.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar leading edge bars are not all identical, so match the number stamped on the parts you removed against A0439 rather than ordering by appearance.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48633648316628,"sku":"CVR-701-3026","price":148.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_e80f1de4-ad4c-4362-a36d-5da01699e9b4.jpg?v=1788808262"},{"product_id":"coverstar-inc-ka0190-apc-repair-ug-slider-large-channel-black-w-screws-set-of-2","title":"Coverstar KA0190 APC Repair UG Slider Large Channel, Black, with Screws, Set of 2","description":"\u003cp\u003eCoverstar KA0190 is the APC repair underguide slider for large channel, molded in black and supplied with screws as a set of two.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe sliders are the wear pieces that ride in the cover track. They carry the rope and the leading edge along the channel, and they are consumed slowly by grit and by every cycle of the cover. When a cover starts to bind, run rough or track unevenly, worn sliders are one of the first things to check.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the large channel version. Coverstar builds sliders to suit different channel sizes, so compare against the part you removed rather than ordering by appearance alone.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48633651691732,"sku":"CVR-KA0190","price":133.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_85ecd01a-f503-43fc-b906-8596c0c2e0fe.png?v=1788808277"},{"product_id":"stop-block-slider-f-wheel-assy","title":"Coverstar Stop Block\/Slider for 403 Series Top Guide System and Wheel Assembly","description":"\u003cp\u003eThe Coverstar M9670 is the stop block and slider for the 403 Series top guide system and wheel assembly. It is the genuine Coverstar part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn automatic cover runs its leading edge along a guide track on each side of the pool. The stop block sets where that travel ends and the slider is the surface the wheel assembly rides against. Both take the load every time the cover opens and closes, which makes them the pieces that wear out first while the track itself stays serviceable.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar lists this part for the 403 Series top guide system, so check which guide system your cover uses. Since the system runs a track on each side of the pool, look at the opposite side at the same time and replace both if they have aged together.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48634420723924,"sku":"CVR-72-9789","price":51.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_3149939c-1cdb-4710-a46c-5ddb8778998b.jpg?v=1788830226"},{"product_id":"coverstar-a3326-4-1-2-wide-lid-bracket-width-extension-kit","title":"Coverstar 4-1\/2\" Wide Lid Bracket Width Extension Kit","description":"\u003cp\u003eThe Coverstar A3326 is the 4-1\/2 inch wide lid bracket width extension kit, genuine Coverstar hardware for the lid assembly on a Coverstar installation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is for\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe extension kit adds width to an existing lid bracket rather than replacing the bracket. It is the part you order when the lid needs to span further than the bracket as fitted allows.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCoverstar lists lid bracket extension kits in more than one width. This is the 4-1\/2 inch wide version, so measure what is on the installation and confirm the size before ordering.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48634490847444,"sku":"CVR-701-A3326","price":34.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6a1a29d0-beee-40e8-89db-ebf4a66a1970.jpg?v=1788832574"},{"product_id":"coverstar-webbing-heat-sealed-per-ft-royal-blue-c0141","title":"Coverstar Heat Sealed Webbing per Foot, Royal Blue","description":"\u003cp\u003eCoverstar C0141 is heat sealed webbing in royal blue, sold by the foot. It is the genuine Coverstar part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWebbing is the flat woven strap used through an automatic pool cover system. Because it is under load every time the cover runs, the edges take a beating, and heat sealing the cut edge is what stops the weave opening up and fraying along the length.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOrdering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is priced and supplied per foot, so measure the run you are replacing and order that many feet. Webbing is trimmed to fit during installation, so it is worth allowing a little extra rather than ending up a few inches short.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48634982891732,"sku":"PSU-165697","price":12.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b5b1168a-a076-4026-b12b-c85b050865fa.png?v=1788839278"},{"product_id":"coverstar-flush-lid-bracket-assembly-a1421","title":"Coverstar Flush Lid Bracket Adjustable Assembly, 13 in. Arm with 7.5 in. Base, A1421","description":"\u003cp\u003eThe Coverstar A1421 is the adjustable flush lid bracket assembly with a 13 in. arm and a 7.5 in. base. It is the genuine Coverstar part for automatic cover vault lids.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it holds up\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA flush lid sits over the automatic cover vault and has to finish level with the surrounding deck. The brackets inside the vault are what carry it and what make that alignment possible. Because they adjust, the lid can be brought back to flush when the deck moves or when the original setting was never quite right.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSizing and options\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis assembly is the 13 in. arm on a 7.5 in. base and is listed as walk-on rated. Where a span needs more reach than the arm gives, extensions are made to work with the bracket. The bracket family is produced in both aluminum and stainless steel, so confirm the material you need with us before ordering.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48641951006932,"sku":"CVR-72-1421","price":99.18,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_7f47d6e4-914b-4935-8f10-a72ad1e776d5.png?v=1788899853"},{"product_id":"coverstar-h1034-tg-standard-wheel","title":"Coverstar TG Standard Wheel","description":"\u003cp\u003eCoverstar H1034 is the TG standard wheel, a genuine Coverstar replacement part for automatic pool cover systems.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy wheels wear out\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eEvery time an automatic cover opens or closes, its wheels carry the cover under load and take grit, sun and pool chemistry along the way. They are consumable, and a worn or seized wheel shows up as a cover that drags, binds or runs unevenly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCover hardware differs between systems and between installation years. Compare the H1034 part number against the wheel you are replacing, and order the quantity your system uses.\u003c\/p\u003e","brand":"Coverstar","offers":[{"title":"Default Title","offer_id":48641951662292,"sku":"CVR-701-4920","price":23.86,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_cbd25404-9ac3-4d41-87e5-96dfbdd0b56b.png?v=1788899908"}],"url":"https:\/\/www.activepoolsupply.com\/collections\/coverstar.oembed","provider":"Active Pool Supply","version":"1.0","type":"link"}