{"title":"Hayward Super II Pump Parts","description":"\u003cp\u003eReplacement parts for Hayward Super II Pump, genuine OEM and compatible aftermarket.\u003c\/p\u003e","products":[{"product_id":"threaded-shaft-motor","title":"Hayward Genuine OEM Max Rate Threaded Shaft Motor 2 HP","description":"\u003cp\u003eThe Hayward SPX1615Z1M is the 2 HP max rate threaded shaft motor used on three of Hayward's most common pumps: the Super Pump SP1600X and SP2600X series, the Super II SP3000X series and the Max-Flo SP2800X series. It is the genuine Hayward part, so it bolts to the seal plate and takes the impeller without adapters.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eElectrical\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe motor is dual voltage, 115 or 230 volts at 60 Hz. Check the voltage setting on the motor against your supply before you wire it, because a 230 V feed into a motor set for 115 V will not last long.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhile the pump is apart\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRemoving the motor means separating the seal plate from the housing and pulling the impeller, which disturbs the shaft seal. Fit a new seal and look over the housing gasket and o-rings before you close it back up; it is far cheaper than doing the job twice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eShipping restriction\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis motor cannot be shipped to California.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48624880287956,"sku":"HAY-101-9769","price":575.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c982bba4-1390-4291-94cd-d8ab57d21e2f.jpg?v=1788648867"},{"product_id":"1hp-motor-threaded-shaft-single-phase-60-cycle-115-230v","title":"Hayward 1HP Motor, Threaded Shaft, Single Phase, 60 Cycle 115\/230V","description":"\u003cp\u003eThe Hayward SPX1607Z1M is a 1 HP single phase replacement motor with a threaded shaft, wired for 115 or 230 volts at 60 cycles. It fits the Hayward Max-Flo, Super Pump and Super II.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat to know before ordering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe motor is built by Century, a Regal brand. Because of DOE energy efficiency regulations it may be replaced with the compatible SP26110Z1MEG, so do not be surprised if that part number arrives instead.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCalifornia\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis motor does not meet the California Energy Commission Title 20 efficiency standard for pool pumps and replacement motors. It cannot be sold or installed in California. Century makes CEC compliant alternatives in its V-Green EVO range, the EVC130, EVC165, EVC225, EVQ130, EVQ165 and EVQ225.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFinish the job\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA motor swap opens the pump wet end, so plan on a new shaft seal and gaskets. Rebuild kits for the Super Pump, Max-Flo and Super II are sold separately.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48624927113428,"sku":"HAY-101-9934","price":403.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_f8cbfb82-7cef-4217-8337-0c7f678c5b81.jpg?v=1788654733"},{"product_id":"3-4hp-3hp-impeller-ring-2-3-4-od","title":"Hayward 3\/4 HP to 3 HP Impeller Ring, 2-3\/4 in. OD","description":"\u003cp\u003eThe Hayward SPX3021R is the Max-Rate impeller ring for 3\/4 HP to 3 HP pumps. It is a plastic ring, 2-3\/4 in. outside diameter and 2-3\/16 in. inside diameter, with SP3021R molded on the part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt is used on the Super II SP3000 and SP3000X, the Northstar in both the 1998 to 2007 and 2008 to current designs, and the TriStar SP3200 and SP3200EE. Measure the old ring against the dimensions above to be sure.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy it matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe impeller ring is the wear surface at the impeller eye. As it wears, the clearance opens up, water recirculates inside the pump and flow falls off. It is a cheap part to replace whenever the pump is apart for a seal or an impeller.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48624997925076,"sku":"HAY-101-6391","price":17.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_f44b3755-4070-4000-9276-c25431506621.png?v=1788661776"},{"product_id":"impeller-diffuser-kit-2-1-2-max-rated-2-hp-full-rate","title":"Hayward Super II Impeller\/Diffuser Kit, 2-1\/2 Max Rated, 2 HP Full Rate","description":"\u003cp\u003eHayward SPX3020CKIT pairs the impeller and the diffuser for Super II pumps rated 2 HP full rate or 2-1\/2 HP max rate. It is the genuine Hayward kit for that wet end.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy they are sold together\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe impeller runs inside the diffuser at a close clearance, and that clearance is what turns motor speed into pressure. Both parts wear. Fitting a new impeller into a diffuser that is already worn opens the gap back up and gives you only some of the flow you were after, so Hayward supplies the two as a kit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck before ordering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSuper II pumps come in several ratings and the impeller is specific to each. Read the horsepower and whether the pump is full rated or max rated off the motor plate. Hayward lists this kit for Super II pumps built in 1989.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat you should see afterwards\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFlow at the returns comes back, filter pressure returns to a normal clean reading, and the pump stops working hard for less water.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48625789960404,"sku":"HAY-101-3035","price":75.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_9f5096ae-44f5-4a8e-9aa2-d9a88cc6a3af.jpg?v=1788700115"},{"product_id":"super-ii-pump-housing-new-style-threaded-2-x-2","title":"Hayward Super II Pump Housing, Threaded, 2\" x 2\"","description":"\u003cp\u003eThe Hayward SPX3120AAZ is the pump housing and strainer for the Super II SP3000 and SP3000X pump series. It is the genuine Hayward part, also written SP-3120-AAZ.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the front half of the pump: the body that carries the suction and discharge connections and holds the strainer basket. It is the threaded version, 2 inch by 2 inch, molded in black plastic. Hayward lists it as the new style housing, so it is worth comparing it to the pump on the pad before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen it needs replacing\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHousings crack at the threads, distort at the sealing face, or split after a freeze. Once the body will not hold prime or will not seal against the strainer cover, no amount of new lids and o-rings will fix it, and the housing itself has to come off.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is not included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe strainer basket, the strainer cover and its hand knob are separate Hayward parts, so plan on inspecting those while the housing is off.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626104533204,"sku":"HAY-101-1409","price":398.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_95479f1e-0d12-41e2-bb44-33dfcc4be8a8.png?v=1788704832"},{"product_id":"75hp-1-5hp-impeller-ring-2-3-8-od","title":"Hayward 0.75 HP to 1.5 HP Impeller Ring, 2-3\/8 in. OD","description":"\u003cp\u003eThe Hayward SPX3005R is the hi performance impeller ring for the Super II pump family. It measures 2-3\/8 in. outside diameter and 1-7\/8 in. inside diameter, and it is matched to the SPX3007C, SPX3010C and SPX3015C impellers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eTwo numbers, one part\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe ring has SP3005R molded into it, so that is the number most people read off the old one when they pull the pump apart. Hayward sells it as SPX3005R. They are the same ring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the ring does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt is the fixed surface the impeller spins inside. The tighter that clearance stays, the more water the pump moves for the same power. As the ring wears the gap opens up, water slips back past the impeller instead of going down the return line, and the pump quietly loses performance without ever sounding wrong.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIf you are already in far enough to see the ring you are in far enough to change the impeller, and the two wear together. Fitting a new impeller into a worn ring recovers only part of the flow you lost.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626367987924,"sku":"HAY-101-2069","price":16.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6ede9760-1f64-4334-8918-b016c68bfe10.gif?v=1788709371"},{"product_id":"seal-assembly-oem","title":"Hayward Seal Assembly, OEM","description":"\u003cp\u003eThe Hayward SPX1600Z2 is the genuine OEM shaft seal assembly used across the Super Pump, Super II, NorthStar and Max-Flo pump families. It also appears in parts lists for the Max-Flo 1800 and 2800 model pumps and for Leslie Hydramax II pumps.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the shaft seal does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe motor shaft passes through the back of the wet end to spin the impeller. The shaft seal is the barrier at that crossing, and it is the only thing keeping pool water out of the motor. It is a two piece assembly, a rotating face carried on the shaft running against a stationary face pressed into the seal plate.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe symptom to look for\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWater dripping from the gap between the motor and the pump body, often with rust streaks or a crusty deposit under it. Left alone, that water works its way into the motor bearings and turns a cheap seal job into a motor replacement.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhile you are in there\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe seal is replaced with the impeller off. Since the pump is already apart, it is worth checking the housing gasket, the impeller and the shaft for wear at the same time.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626378375380,"sku":"HAY-101-2020","price":33.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_ecf4f78c-bedd-43af-98a6-4217eac382f2.jpg?v=1788709509"},{"product_id":"seal-plate-2","title":"Hayward Seal Plate for Super II Pump","description":"\u003cp\u003eThe Hayward SPX3020E is the seal plate for Super II pumps, also listed as SP3020-E. It is the molded plastic plate that bolts between the motor and the pump body and carries the shaft seal.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eEverything the pump has to keep separate meets at this plate: wet volute on one side, motor and bearings on the other. The plate holds the stationary ceramic half of the shaft seal, so if it is cracked, warped from a dry run, or the seal seat is scored, water works its way past even a brand new seal and ends up in the motor.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward lists it for the Super II SP3000 and SP3000X, and it also appears in the parts breakdowns for the Heldor EZ-Flo and the Leslie Hydramax II pumps from SP-LE40010 through SP-LE40019.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe manufacturer information supplied for this part is not consistent about horsepower. One listing gives 2 HP and 3 HP, another gives 2-1\/2 HP and 3 HP. Rather than pick by horsepower, check that SPX3020E is the seal plate called out for your specific pump. While the pump is open, plan on a new shaft seal too, since it is sold separately and there is no reason to reuse the old one.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626391220436,"sku":"HAY-101-2074","price":68.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_787c1c54-b6c4-4fa1-b721-4c2e2b869222.png?v=1788709718"},{"product_id":"diffuser-1-5hp-3hp-fr","title":"Hayward Super II Diffuser, 1-1\/2 HP to 3 HP Full Rate","description":"\u003cp\u003eThe Hayward SPX3021B is the replacement diffuser for Super II pool pumps in the 1-1\/2 HP through 3 HP full rate range. It is the genuine Hayward part, molded in plastic like the one it replaces.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the diffuser does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe diffuser sits over the impeller and directs the water leaving it into the volute. That shaping is what turns impeller speed into pressure and flow. A diffuser that is cracked, warped, or worn around the impeller opening lets water slip back instead of moving forward, and the pump loses output even though the motor sounds exactly the same.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMatch the horsepower\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward uses different diffusers across the Super II range, so horsepower matters when you order. This one covers 1-1\/2 HP to 3 HP full rated pumps and also serves the Heldor EZ-Flo pumps built on the same body.\u003c\/p\u003e\u003cp\u003eBecause the pump has to come apart to reach the diffuser, it is a good moment to look at the diffuser gasket, the impeller ring and the seal plate. Those are separate parts and all of them are far easier to change now than on a second teardown.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626510659796,"sku":"HAY-101-6304","price":54.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_eb5bba55-152a-4c0c-bbd6-0c91ea2ed220.png?v=1788711121"},{"product_id":"impeller-2-hp-max-rated-1-hp-full-rate","title":"Hayward 1.5 HP FR Super II Impeller, After 1989","description":"\u003cp\u003eThe Hayward SPX3016C is the replacement impeller for Super II pumps built after 1989. It is the genuine Hayward part, molded in plastic to the same shape as the one that left the factory.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the impeller does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe impeller is the spinning vane pack inside the pump that actually moves the water. It wears from the inside out: the vane edges round off, the passages pack with debris and scale, and the pump loses pressure and turnover long before it makes any obvious noise. Owners often replace a filter or chase a suction leak when the impeller is what has gone.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHorsepower rating\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe records for this part do not agree on how to describe its rating. The product listing calls it the 1.5 HP full rate impeller. The catalog record calls it 2 HP max rated and 1 HP full rate. Both refer to Hayward SPX3016C, so the safest check is the rating molded into the impeller you are taking out.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitment\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSuper II SP3000 and SP3000X, plus Heldor EZ-Flo pumps that use the same wet end, on units built after 1989.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626590974164,"sku":"HAY-101-7322","price":64.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_21b556e9-c6d0-4bed-a905-470cd780c282.png?v=1788712792"},{"product_id":"slinger-for-motor-shaft","title":"Hayward Slinger for Motor Shaft","description":"\u003cp\u003eThe Hayward SPX0125F is the motor shaft slinger used on the Super Pump, Super II and Max-Flo families. It is a small molded plastic ring that sits on the motor shaft, and it is also listed under the number G-71.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is there for\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWater that works its way past the shaft seal has to go somewhere. The slinger turns with the shaft and flings that water outward, away from the motor end, instead of letting it creep along the shaft and into the bearings. It costs almost nothing and it is the difference between a wet seal plate and a ruined motor.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitment\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward lists it for the Super II SP3000 and SP3000X, the Super Pump SP2600X and SP1600X, and the Max-Flo SP2800X. It also shows up in the Leslie's Hydramax II pump parts listing for models SP-LE40010 through 40019.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to fit one\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAny time the motor is separated from the wet end. If you are in there for a shaft seal, an impeller or a motor swap, put a fresh slinger on while the shaft is bare.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626712740052,"sku":"HAY-101-1961","price":13.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_d827d56b-9c61-4cb2-8b20-c8ae53062176.png?v=1788713965"},{"product_id":"impeller-1-1-2hp-max-rated-1hp-full-rate","title":"Hayward Impeller, 1-1\/2 HP Max Rated, 1 HP Full Rate","description":"\u003cp\u003eThe Hayward SPX3010C is the genuine replacement impeller for Super II pumps rated 1 HP full rate and 1-1\/2 HP max rate. It carries SP3010-C stamped into the outer face, which is the marking to check against the impeller you take out.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMatching the part\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward built the Super II across a range of horsepowers and each one uses its own impeller, so the number matters more than the label on the motor. Take the old impeller off, read the stamp on the outer face, and match it. If it reads SP3010-C, this is the part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat a worn impeller looks like\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFlow at the returns falls off, filter pressure sits lower than it used to, and the motor sounds perfectly healthy while it happens. Either the vanes are packed with debris that will not clear, or they have worn thin. Once the impeller is out and the vanes are visibly rounded off or broken, the pump will not get its performance back without a new one.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626990285012,"sku":"HAY-101-2071","price":53.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b3d52065-9ea5-4787-8fbe-3bd2f6a90dd2.png?v=1788718799"},{"product_id":"diffuser-gasket-o-ring","title":"Hayward Super Pump\/Super II Diffuser Gasket","description":"\u003cp\u003eThe Hayward SPX1600R is the diffuser gasket for the Super Pump, Super II and Max-Flo pump series. It is a molded rubber o-ring, the genuine Hayward part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it seals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe diffuser sits over the impeller and shapes the flow leaving it. The gasket is what holds that joint tight. When it flattens or hardens, water takes the shortcut around the diffuser instead of through it, and the pump moves noticeably less water for the same amount of noise and current.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to change it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe diffuser has to come out for almost any seal or impeller job, so this is the moment to fit a fresh gasket. A rebuilt pump that still underperforms is often a rebuild that reused a tired diffuser gasket.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48627000443092,"sku":"HAY-101-2016","price":10.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_9aa346ac-7cd9-47af-89d1-ab9d77b28ad0.gif?v=1788718916"},{"product_id":"diffuser-5hp-1-5hp-fr-75hp-2hp-ur","title":"Hayward Super II Pump Diffuser, .5 HP to 1.5 HP Full Rate, .75 HP to 2 HP Up Rated","description":"\u003cp\u003eThe Hayward SPX3000BN is the genuine replacement diffuser for the Super II pump, covering models rated .5 HP to 1.5 HP full rate and .75 HP to 2 HP up rated. It is molded in plastic, the same as the original.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the diffuser matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe diffuser wraps the impeller and turns the speed of the water leaving the vanes into usable pressure. A cracked or distorted diffuser lets water recirculate instead of moving forward, so the pump sounds normal but the filter gauge and the return flow both drop.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat to look for\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCheck the face where the impeller runs for cracks, look at the mounting bosses for chips, and see whether the part still seats tightly. Any of those means the diffuser is done.\u003c\/p\u003e\u003cp\u003eIf you are already replacing the impeller or the shaft seal, do the diffuser at the same time. The pump is apart, the parts wear together, and a new impeller in a worn diffuser will not give you the flow you paid for.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48627359154388,"sku":"HAY-101-2059","price":52.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_9c0467dd-9cf9-42d3-8d18-44ee89dc08ea.png?v=1788722827"},{"product_id":"hayward-spx1605z1m-maxrate-motor-for-superpump-sp1600x-pool-pumps-3-4-hp","title":"Hayward MaxRate Motor for Super Pump SP1600X Pool Pumps, 3\/4 HP","description":"\u003cp\u003eThe Hayward SPX1605Z1M is a 3\/4 HP MaxRate replacement pump motor with a threaded shaft, rated 115\/230 V at 60 Hz.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck the fitment carefully\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis part is described two ways in our source. The listing title puts it on Super Pump SP1600X series pumps. The manufacturer description puts it on Max-Flo SP1800X and SP2800X and Super II SP3000X series pumps. We have carried both readings here rather than picking one. Before ordering, read the data plate on the motor you are removing and confirm the pump model, horsepower, voltage and frame.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat a motor swap involves\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe motor drives the impeller through a threaded shaft, and the seal between the two is a wear item that gets disturbed the moment the wet end comes apart. Plan on a new shaft seal, and inspect the housing gasket and the diffuser while everything is open. Fitting a new motor to a tired seal is the most common reason a rebuilt pump starts weeping a week later.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eElectrical\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe motor is rated for 115 V or 230 V at 60 Hz. Wiring and voltage selection should be done by a qualified electrician, and the breaker should be off before anything is opened at the pad.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48627383501012,"sku":"HAY-101-2085","price":367.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/Spx1605Z1M_motor.jpg?v=1788722958"},{"product_id":"drain-plug-with-gasket","title":"Hayward Drain Plug with Gasket for Select Hayward Equipment","description":"\u003cp\u003eThe Hayward SPX1700FG is the drain plug with gasket for Hayward pool pumps made after 1991. It is the genuine Hayward part and it is supplied with the gasket already fitted.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is for\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe drain plug sits low on the pump and is what you pull to empty the volute. That happens twice in a normal year: once when the pump is winterized so trapped water cannot freeze and crack the housing, and again whenever the wet end has to come apart for service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy they get replaced\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe gasket is the weak point. It hardens with age, and it gets pinched, torn or simply lost during winterizing when the plug is taken out in the cold and set down somewhere. Once it is gone the plug will not seal and the pump takes air, so it is worth keeping a spare with the winterizing kit.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48627840319700,"sku":"HAY-101-2034","price":10.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_7a1327f3-76dd-49a4-ba1c-9e96735b742a.png?v=1788728070"},{"product_id":"strainer-cover-lid","title":"Hayward Super II Hand Knob Strainer Cover","description":"\u003cp\u003eThe Hayward SPX3000D is the clear hand knob strainer cover for the Super II SP3000 and SP3000X pump series. It is the genuine Hayward replacement, in plastic, with the knob molded in so it tightens by hand.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy lids fail\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe strainer cover is the one part of a pump that is opened every week. Sun, heat and repeated tightening craze the plastic until it cracks, and a cracked lid pulls air rather than water. A pump that loses prime, spits air at the returns or runs with a half full basket is very often telling you about its lid.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the cover itself, with its hand knob. The lid o-ring is a separate part, and since a new cover will only seal as well as the ring under it, that is worth checking while the pump is open. The cover is also listed under Heldor EZ-Flo pump parts.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48627924107476,"sku":"HAY-101-2060","price":84.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4e59b4f5-d246-467a-a103-192da0594460.gif?v=1788729867"},{"product_id":"impeller-2-hp-max-rated-1-1-2-hp-full-rate","title":"Hayward Impeller, 2 HP Max Rated, 1-1\/2 HP Full Rate","description":"\u003cp\u003eThe Hayward SPX3015C is the genuine OEM impeller for Super II pool pumps, rated 2 HP max rate and 1-1\/2 HP full rate. It fits the SP3000 and SP3000X Super II pumps and the Heldor EZ-Flo.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat a worn impeller looks like\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFlow falls off gradually, so it rarely announces itself. The usual sequence is a clean pump basket, a clean filter, normal water level, and still less return pressure and weaker suction than the pool used to have. Debris packed hard into the vanes causes it, and so does simple wear that thins the vane edges over years of running.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eGetting the rating right\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eImpellers are matched to the pump rating, not just to the pump family. This one covers the 2 HP max rated and 1-1\/2 HP full rated Super II. Check the label on your motor against those figures before ordering, since fitting the wrong impeller loads the motor incorrectly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhile you are in there\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe impeller comes off during the same teardown that exposes the seal and the wear ring, so it is worth inspecting both while the pump is apart.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48627976765652,"sku":"HAY-101-2072","price":62.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6a2edde9-3e96-41a6-a405-65ca1a5724cc.png?v=1788732117"},{"product_id":"impeller-1-hp-max-rated-3-4-hp-full-rated","title":"Hayward Super II Impeller, 3\/4 HP Full Rated, After 1987","description":"\u003cp\u003eThe Hayward SPX3007C is the genuine impeller for Super II pumps built after 1987, rated 3\/4 HP full rated and 1 HP maximum rated.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe two horsepower numbers\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFull rated and maximum rated are two ways of describing the same motor and impeller combination, which is why one part carries both figures. If your pump is labelled 3\/4 HP full rated or 1 HP up rated, this is the impeller for it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe 1987 split\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward changed the Super II impeller design, and parts before and after that change are not interchangeable. SPX3007C is the later part, for pumps built in 1988 and after. Confirm the age of the pump, or match the number stamped on the old impeller, before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhile the pump is open\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGetting to the impeller means the wet end is already apart. That is the sensible time to look at the diffuser, the impeller ring and the shaft slinger, all of which wear alongside the impeller and cost far less than a second teardown.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48628797800660,"sku":"HAY-101-2070","price":53.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_a3acc1b2-ae7e-41f2-a3b0-3e6493b25210.png?v=1788750810"},{"product_id":"impeller-1-hp-max-rate-3-4-hp-full-rate","title":"Hayward Impeller, 1 HP Max Rate, 3\/4 HP Full Rate","description":"\u003cp\u003eThe Hayward SPX2607C is the genuine impeller for 3\/4 HP full rate and 1 HP max rate pumps. It is fitted across the Super Pump, Super II, Power-Flo II and Leslie Hydramax above ground families.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRating matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn impeller is cut for a specific horsepower. Fitting the wrong one either starves the pump or overloads the motor, so match the 3\/4 HP full rate and 1 HP max rate designation to the plate on your motor rather than to the pump body. Two pumps that look identical from the outside can take different impellers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSymptoms of a worn impeller\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWeak flow at the returns while the motor sounds and draws normally is the classic sign. So is a pump that has swallowed something and never fully recovered its prime. Debris packed into the vanes chokes the passage, and once the vane edges are worn round the impeller cannot make pressure however clean it is.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePlan the job\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe shaft seal comes off to reach the impeller and it does not go back on. Order the seal with the impeller, look at the impeller ring while the pump is apart, and you will only open the wet end once.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48628807401684,"sku":"HAY-101-2053","price":49.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4a04169f-99f3-4505-a1af-5b6e68841bed.png?v=1788751947"},{"product_id":"hayward-spxhkit2-quick-pump-repair-replacement-kit-for-hayward-super-ii-pool-pumps","title":"Hayward Super II Pump Quick Fix Kit","description":"\u003cp\u003eThe Hayward SPXHKIT2 is the quick fix kit for Super II pumps in the SP3000 and SP3000X series. It gathers the parts a leaking pump usually needs into a single order.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat you get\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA strainer cover o-ring, a housing gasket, a seal assembly, a diffuser gasket and lube. Between them those cover the lid, the split between the housing and the seal plate, the shaft and the diffuser.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy do them all together\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe pump has to come apart for any one of these repairs. Once it is open, the labor is already spent, and the remaining seals are the same age as the one that failed. Doing the set is why the kit exists.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSymptoms\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWater weeping around the strainer lid, a drip appearing behind the seal plate, or a pump that will not hold prime are the usual reasons to reach for this kit.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48628829749460,"sku":"HAY-101-9943","price":44.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/hayward-spxhkit2-super-ii-pump-quick-fix-kit.jpg?v=1788753589"},{"product_id":"super-ii-pump-housing-new-style-threaded-1-5-x-1-5","title":"Hayward Super II Pump Housing, Threaded, 1.5\" x 1.5\"","description":"\u003cp\u003eSPX3100AAZ is the Hayward Super II pump housing, the new style threaded version, supplied with drain plugs. It is the strainer pot and body the basket sits in and the plumbing threads into.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen the housing is the part you need\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA pump housing is not usually a wear item. It gets replaced when it cracks, and the two common causes are water left in the pot through a freeze and a fitting threaded in too hard. Either one leaves the pump losing prime or leaking at a place no o-ring will fix.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck the style\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward changed the Super II housing partway through the pump run. This is the later threaded housing, and it is listed with the Super II SP3000, SP3000X and Heldor EZ-Flo parts. Compare it against what is on your pump before ordering.\u003c\/p\u003e\u003cp\u003eThe basket, the strainer cover and its lid are separate Hayward parts and are not included with the housing.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48628834402516,"sku":"HAY-101-1210","price":392.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c7b9a286-3f3f-435f-985f-d3624d591e83.png?v=1788753771"},{"product_id":"o-ring-for-trap-cover-strainer-pot","title":"Hayward O-Ring for Trap Cover Strainer Pot","description":"\u003cp\u003eThe Hayward SPX3000S is the lid o-ring that seals the trap cover to the strainer pot on the Super II pool pump. It is also listed under the substitute part number O-12.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe seal that holds prime\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eEverything upstream of the pump impeller is under vacuum, and the trap cover is the largest removable joint on that side of the system. When the o-ring under it is fresh and pliable, the joint holds. When it has flattened, hardened or cracked, air gets pulled in past it, and the symptom is a pump that will not hold prime or a basket that never fills.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to change it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAny time the trap cover is off for another reason, look at the o-ring while it is in your hand. If it has taken a permanent set in the shape of the groove, or feels stiff rather than rubbery, replace it. It is the cheapest part on the pump and one of the most common causes of a service call.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48628850458836,"sku":"HAY-101-2066","price":24.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_37dd6945-6d60-41ac-8db6-025f493eb0d7.jpg?v=1788755303"},{"product_id":"oem-super-ii-strainer-basket","title":"Hayward OEM Super II Strainer Basket","description":"\u003cp\u003eThe Hayward SPX3000M is the factory strainer basket for Super II pool pumps, and it is also listed under the number B-207. It measures 5.75 inches by 8.75 inches and is molded in plastic.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the basket does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eEverything the skimmer misses arrives at the pump. The strainer basket catches leaves, twigs and hair before the water reaches the impeller, which is why a basket that has split at the rim or cracked through the wall is worth changing straight away. Debris that gets past a broken basket lodges in the impeller vanes and starves the pump of flow.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck the size first\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward uses several basket sizes across its pump lines, and they do not swap. Pull your old basket and check it against the 5.75 inch by 8.75 inch dimensions before ordering. Beyond the Super II, this same basket is cataloged for Heldor EZ-Flo pumps and for Leslie Hydramax II pumps in the SP-LE40010 through 40019 range.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48628865597652,"sku":"HAY-101-2064","price":30.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4609597c-ee07-4f83-83c6-24f23c3f935d.jpg?v=1788756740"},{"product_id":"hand-knob-kit","title":"Hayward Hand Knob Kit","description":"\u003cp\u003eThe Hayward SPX1600PN hand knob kit is the clamping hardware for the strainer cover on Super Pump and Super II pumps. It ships as a set: the swivel nut and the hand knob together.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy it wears out\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe knob is turned by hand every time a basket is emptied, and it sits in sun and pool chemicals the rest of the time. Threads round off, the plastic goes brittle and eventually the cover will not pull down tight. That is when the pump starts drawing air, losing prime or dribbling water at the lid.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBecause the kit includes the swivel nut, both halves of the worn assembly get replaced at once. While the cover is off, look at the lid o-ring as well. A tired o-ring and a tired knob usually reach the end together, and replacing only one of them rarely stops the air leak.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48628890534100,"sku":"HAY-101-2086","price":26.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6e1bc540-ee3c-4849-9e5d-11c224e8e452.png?v=1788757004"},{"product_id":"motor-mounting-plate","title":"Hayward Motor Mounting Plate for Super II Pump","description":"\u003cp\u003eThe Hayward SPX3000F is the motor mounting plate for the Super II pump. It is the molded plastic plate the motor sits on, and it holds the motor square to the seal plate so the shaft and impeller stay in line.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy it fails\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe plate takes the whole weight of the motor and every knock the pump receives. Cracks through the feet, broken mounting bosses and distortion from over tightened hardware are the usual reasons it comes out. A pump running on a broken plate sits off line, which puts the shaft seal under load it was never meant to carry.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting notes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward lists this part across the Super II, the Super Spa pump in the SP-3500 uprated group and the Leslie Hydramax II pumps. Since the motor has to come off to change the plate, it is the natural moment to look at the shaft seal and the seal plate as well.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48628942176468,"sku":"HAY-101-2062","price":71.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_e2a91634-3909-4c06-b20b-6e360d6983d9.png?v=1788758294"},{"product_id":"clear-lexan-strainer-lid-thread-in-style-super-ii","title":"Hayward Clear Lexan Strainer Lid, Thread In Style (Super II)","description":"\u003cp\u003eThe Hayward SPX3100D is the clear thread in strainer lid for the Super II pump. It is the genuine Hayward replacement, and Hayward also lists it for the Heldor EZ-Flo, the C250CF and C500CF chlorine feeders, and Leslie's Hydramax II pumps in the SP-LE40010 through 40019 range.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eConfirm the style first\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward has used several lid designs across its pumps. This one threads into the pot. If the lid on your pump is held by a hand knob or a clamping ring, it is a different part, and the two do not swap.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy lids get replaced\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA clear lid lets you look at the basket and the water in the pot without shutting anything down, which is worth having. The trade is that it takes UV, heat and chemistry all season, so it clouds and eventually goes brittle. That is not just cosmetic. A brittle lid can split under load, and the pump loses prime immediately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDo the o-ring at the same time\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe lid seals against a trap cover o-ring, which is a separate part. If the pot has been sucking air or dripping, the o-ring is the first suspect and it makes sense to change both while the pump is open.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48629291188436,"sku":"HAY-101-5622","price":76.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_137f949b-4743-4cfb-94f7-db6af6700a4a.jpg?v=1788762013"},{"product_id":"motor-cap-screw-4-per-pack","title":"Hayward Motor Cap Screw (4 per Pack)","description":"\u003cp\u003eThese are the genuine Hayward SPX0125Z44 motor cap screws, four to a pack. Hayward lists them for the Super, Super II, Max-Flo and NorthStar pumps.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy a pack of four\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eFour is a set for one motor. It is rarely worth replacing one screw and leaving three originals in place, because the ones you did not touch are the same age and have had the same weather.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThese are the ones that seize\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe motor cap screws sit right in the weather on the equipment pad, and after a few seasons they corrode into the threads. Most people find this part after rounding off a head trying to get a motor apart. Ordering the set ahead of a motor job saves the extraction.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48629291450580,"sku":"HAY-101-1963","price":18.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_a0d817cc-37ee-40c5-8a5f-5d29be94a63b.png?v=1788762017"},{"product_id":"seal-assembly-kit-1","title":"Hayward Seal Assembly Kit for Super II Pump","description":"\u003cp\u003eThe Hayward SPX3000TRA is the seal assembly kit for the Super II pump. It is a three piece kit: the seal assembly itself, the housing gasket and the diffuser gasket, all supplied together.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the shaft seal does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe seal rides on the motor shaft where it passes into the wet end and keeps pool water on the pump side of that opening. It is a wearing part. When it goes, water escapes between the motor and the housing and runs down toward the motor, which is why a leak there should not be left alone.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the gaskets are included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGetting to the seal means opening the pump, so the housing and diffuser gaskets have to come off anyway. Hayward packs replacements in the kit so the pump is put back together on fresh rubber instead of on compressed, years old gaskets that will weep again.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48629386674388,"sku":"HAY-101-3000","price":61.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_2446b2be-70db-4002-8bf8-b7e4d8ee1d8a.png?v=1788765862"},{"product_id":"drain-plug-1-4","title":"Hayward Drain Plug 1\/4\"","description":"\u003cp\u003eThe Hayward SPX1600V is the 1\/4 inch drain plug for Super and Super II pumps built in 1991 and prior. It is the genuine Hayward part, in plastic.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe plug that does the most work\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAlmost every other part of a pump stays where it is. The drain plug comes out at the end of every season so the housing can empty before the first freeze, and goes back in every spring. That handling is what wears the thread and rounds off the head, until one autumn it will not come out at all.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eTwo things to check. That your pump is a Super or Super II from 1991 or earlier, and that you need the 1\/4 inch size. If you want the version supplied with a gasket, that is a different Hayward part number.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48633441943764,"sku":"HAY-101-2019","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_a03a3d35-104b-4ccb-9479-70eda21b38f0.png?v=1788801809"},{"product_id":"housing-gasket-3000-series","title":"Hayward Housing Gasket, 3000 Series","description":"\u003cp\u003eThe Hayward SPX3000T is the rubber housing gasket used on 3000 series pumps. Hayward lists it for the Super II SP3000 and SP3000X and for the Heldor EZ-Flo, and the same part shows up in the Leslies Hydramax II parts listing for models SP-LE40010 through 40019.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it seals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe gasket sits at the joint where the pump housing meets the seal plate. It has to hold that face watertight while the pump runs under suction on one side and pressure on the other. Over years of heat cycling the rubber hardens, takes a permanent set and loses the squeeze it needs, which shows up as a slow weep at the seam rather than an obvious leak.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to change it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAny time the pump comes apart, this gasket is worth replacing rather than reusing. Refitting a compressed gasket onto a clean face is the most common reason a rebuilt pump still drips.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48633927467220,"sku":"HAY-101-2067","price":22.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_517a1d19-6ff4-42f5-9141-eed33e06a88d.png?v=1788817355"},{"product_id":"impeller-1-1-2-hp-max-rate-1-hp-full-rate","title":"Hayward Impeller, 1-1\/2 HP Max Rate, 1 HP Full Rate","description":"\u003cp\u003eThe Hayward SPX2610C is the replacement impeller rated 1 horsepower full rate and 1-1\/2 horsepower max rate. It is the genuine Hayward part, molded in plastic like the original.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMatch the horsepower\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eImpellers are not interchangeable across a pump family. Two pumps with identical housings can take different impellers depending on how the motor is rated, so read the motor label rather than the pump model when you order. This one covers the 1 HP full rate and 1-1\/2 HP max rate combination.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it is listed\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward shows this impeller on the Super Pump SP1600, 1600X, 2600 and 2600X, the Super II SP3000 and SP3000X including the Heldor EZ-Flo, the Power-Flo II SP1700 and SP1700UN, and the Leslie's Hydramax above ground pumps. It also turns up on the Max-Flo 1800 and 2800 diagrams, so if you have a Max-Flo, confirm against that diagram before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhile you are in there\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGetting to the impeller means taking off the seal plate, which puts the mechanical seal and the shaft slinger in your hand. Both are cheap and both are wear items, and replacing them at the same time saves stripping the pump twice.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48633932972244,"sku":"HAY-101-2054","price":49.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c29d7106-bf3e-49df-913d-b95b54005760.png?v=1788817583"},{"product_id":"impeller-2-hp-max-rate-1-1-2-hp-full-rate","title":"Hayward Super Pump and Super II Impeller, 2 HP Max Rate \/ 1-1\/2 HP Full Rate","description":"\u003cp\u003eThe Hayward SPX2615C is the genuine impeller for Super Pump and Super II pumps, rated 2 HP max rate and 1-1\/2 HP full rate. It fits Super Pump models SP1600, SP1600X, SP2600 and SP2600X and Super II models SP3000 and SP3000X, including the Heldor EZ-Flo.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMatch the horsepower\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward builds a different impeller for each horsepower in the range, and they look similar enough to be mixed up. Fitting the wrong one leaves the pump underperforming or overloads the motor. Read the label on your motor and match the rating rather than going by the shape of the old part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy impellers get replaced\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe impeller is the piece that actually moves the water. Vanes thin out over the years, and the narrow passages inside pack with hair, grit and small debris that a torn basket let through. Either way the pump keeps running while flow and filter pressure quietly fall. Since the impeller comes off over the shaft seal, most people fit a new seal assembly at the same time.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48634472005844,"sku":"HAY-101-2055","price":62.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_d8a7e58a-29ab-440b-8162-ec7ea7d81179.png?v=1788831752"},{"product_id":"impeller-3-4-hp-max-rate-1-2-hp-full-rate","title":"Hayward Impeller, 3\/4 HP Max Rate, 1\/2 HP Full Rate","description":"\u003cp\u003eThe Hayward SPX2605C is the genuine impeller for 1\/2 horsepower full rate and 3\/4 horsepower max rate pumps. Hayward rates the same hydraulic size two ways, which is why one part covers both descriptions.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eConfirming the right part\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe surest check is the stamp. SP2605-C is molded into the front face of the impeller, so pull the old one and read it rather than working backwards from the horsepower printed on a pump label that may predate a motor swap.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt serves the Super Pump family in the SP1600, SP1600X, SP2600 and SP2600X models, and the Super II family in SP3000 and SP3000X, including the Heldor EZ-Flo build.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat a worn impeller costs you\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eVanes thin out with years of grit passing through them and the passages pack with hair and leaf fiber. The motor still draws its current and the pump still sounds normal, but head drops off, returns go soft and a pressure or suction cleaner starts stalling. Because the mechanical seal has to come off to reach the impeller, plan on a new seal assembly in the same visit.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48634492223700,"sku":"HAY-101-2051","price":50.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_e19dabdb-979b-4290-88d9-de9451bd97b7.png?v=1788832708"},{"product_id":"diffuser-5hp-1-5hp-fr-2-5hp-3hp-ur","title":"Hayward Super II Pump Diffuser, 1\/2 HP to 1-1\/2 HP Full Rated and 2-1\/2 HP to 3 HP Up Rated","description":"\u003cp\u003eThe Hayward SPX3000B is the replacement diffuser for the Super II pump, covering the 1\/2 HP to 1-1\/2 HP full rated and 2-1\/2 HP to 3 HP up rated models. It is the genuine Hayward part and is also listed for the Heldor EZ-Flo.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the diffuser does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe diffuser sits over the impeller and directs the water thrown off it into the pump volute. The gap between the two is part of how the pump makes pressure, so when a diffuser cracks, warps from heat or wears at the eye, water simply recirculates inside the housing. The pump sounds normal and the motor draws current, but the flow at the returns falls off.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCheck the horsepower and the full rated or up rated marking on your motor label, since Hayward splits Super II diffusers by that range. This listing is the diffuser only. The gasket that seals it, the impeller and the impeller ring are ordered separately if they are worn too.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48634495566036,"sku":"HAY-101-2058","price":39.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_34b9a216-52f5-460d-a8db-94b0c019574f.png?v=1788832867"},{"product_id":"screw-1","title":"Hayward SPX1600Z4 Housing Cap Screw","description":"\u003cp\u003eThe Hayward SPX1600Z4 is the housing cap screw used on the Super Pump and Super II and on a number of other Hayward and Jandy Laars products. It is the genuine Hayward part, given as 3\/8-16 x 2.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it is used\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward lists it under the Super Pump SP1600, SP1600X, SP2600 and SP2600X, and the Super II SP3000 and SP3000X including the Heldor EZ-Flo. The same fastener is carried under the Max-Flo 1800 and 2800, the Leslie's Hydramax II, the Super Spa SP-3500, an HRP sand filter group and several Jandy Laars Series 2 and Lite heater diagrams. That is a broad list for one screw, so measure the one you are replacing against the 3\/8-16 x 2 size rather than ordering on the model name alone.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe practical problem\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThese screws sit in a wet, chlorinated environment for years and then have to come out during a service. Many do not, or they come out with the head chewed. Work them with penetrating oil and time rather than force, because a screw snapped off inside a housing turns a routine job into an extraction. When you do get them out, it is usually worth replacing the whole set: they have all seen the same water and the same heat.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48634971521236,"sku":"HAY-101-2021","price":11.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_dca86055-2c5a-4175-90aa-db9207d15eb5.png?v=1788839218"},{"product_id":"mounting-foot-cap-screw","title":"Hayward Mounting Foot Cap Screw, Set of 2","description":"\u003cp\u003eThese are the Hayward SPX1600Z52 mounting foot cap screws, supplied as a set of two. They are the genuine Hayward hardware.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitment\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHayward lists this screw across a wide range of equipment: Super Pump SP1600, SP1600X, SP2600 and SP2600X, Super II SP3000, SP3000X and Heldor EZ-Flo, NorthStar from both the 1998 to 2007 and the 2008 to current runs, Max-Flo XL, and the Super Spa SP-3500 uprated. It also appears in the Perflex EC65, EC65A, EC75 and EC75A DE filter parts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy buy new hardware\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eMounting foot screws sit low on the equipment pad, in the splash and the damp, and they corrode. The usual discovery is that a screw rounds off or shears halfway through a pump service, and what should have been a quick job becomes drilling and retapping. Fitting new screws when the old ones look rough costs very little next to that.\u003c\/p\u003e\u003cp\u003eThey come as a pair because the foot takes two, and because a screw that has corroded has a twin that has seen exactly the same conditions.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48635037155540,"sku":"HAY-101-1393","price":11.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6bc996b4-ba4b-4a4c-a934-9add1469bb7e.png?v=1788840189"},{"product_id":"impeller-3-hp-max-rated","title":"Hayward SUPER II IMPELLER 3 HP FR \/ 3HP MR | SPX3026C","description":"\u003cp\u003eHayward SUPER II IMPELLER 3 HP FR \/ 3HP MR. OEM part number SPX3026C.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48648863350996,"sku":"HAY-101-2076","price":72.97,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/43842_1_201082591739.jpg?v=1789059421"}],"url":"https:\/\/www.activepoolsupply.com\/collections\/hayward-super-ii-parts.oembed","provider":"Active Pool Supply","version":"1.0","type":"link"}