{"title":"Hydro-Quip","description":"\u003cp\u003eHydro-Quip pool equipment and replacement parts at Active Pool Supply.\u003c\/p\u003e","products":[{"product_id":"5-5kw-balboa-heater-assy-w-m7-sensors-studs","title":"Hydroquip 5.5 kW Balboa Heater Assembly with M7 Sensors and Studs","description":"\u003cp\u003eThe Hydro-Quip 26-58083-K is a 5.5 kW Balboa heater assembly supplied with the M7 sensors and terminal studs fitted. It is meant for Balboa based spa control packs that use the M7 sensor arrangement.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOrdering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBecause the sensors and studs are included, this is a complete swap rather than a bare element. Match the part number 26-58083-K to your spa pack paperwork, and confirm the 5.5 kW rating matches the heater you are replacing.\u003c\/p\u003e\u003cp\u003eThe assembly ships by parcel.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48624927703252,"sku":"HQP-851-0040","price":162.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/26-58083-k-55kw-balboa-heater-assy-w-m7-sensors-studs.jpg?v=1788654787"},{"product_id":"laing-10-0102-120-240v-75-barb-e5-spa-circulation-pump-with-4-cord","title":"Laing Thermotech E5 Spa Circulation Pump with 4' Cord, 120\/240V, 3\/4\" Barb","description":"\u003cp\u003eThe Laing Thermotech E5, part 10-0102-K, is a spa circulation pump with 3\/4 in. barb connections and a 4 ft cord fitted. It is the current replacement for the SilentFlo 5000 (72204) and all earlier single speed circulation pumps on Caldera, Hot Spring and Tiger River spas, where it carries the Watkins part number 74427. HydroQuip lists it as 10-0102-K and Laing as E5-NCHNNNN3W-10.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePerformance\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe E5 draws 39 watts and moves up to 6,000 gallons of water in 24 hours, a step up in capacity over the models it replaces. The magnetic drive starts gradually and primes with water reliably.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRun it wet\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe pump is water lubricated and should only be run with water in the spa. If it does run dry, a thermal cut-off shuts it down before it overheats; switch it off for 10 seconds and back on to reset.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWiring note\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis newer model no longer needs a bonding lug. Connect the green wire in the cord to a grounding location inside the controller.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48625023025364,"sku":"HQP-85-0102","price":201.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/HQ100102.jpg?v=1788662569"},{"product_id":"4kw-balboa-heater-assy-w-m7-sensors-studs","title":"Hydroquip 4Kw Balboa Heater Assembly with M7 Sensors and Studs","description":"\u003cp\u003eThe Hydroquip 26-58104-K is a 4 kW Balboa heater assembly supplied with M7 sensors and studs.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is in the assembly\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRather than a bare element, this is the complete heater assembly with its M7 sensors and the mounting studs already included. That matters on a service call, because the sensors and studs are exactly the small parts that hold up a repair when they are ordered separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRating\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe assembly is rated at 4 kW. Confirm the output your system calls for before ordering, since Balboa heater assemblies are made in more than one rating and the wrong one will not heat as the pack expects.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48625746116820,"sku":"HQP-851-0041","price":162.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/26-58104-k-4kw-balboa-heater-assy-w-m7-sensors-studs.jpg?v=1788690884"},{"product_id":"pressure-switch-4037p","title":"Hydroquip Pressure Switch, 4037P","description":"\u003cp\u003eThis is the Hydroquip replacement pressure switch, part number 34-0019-C, listed by Hydro-Quip as the 4037P. It is a straight replacement for the original switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat a pressure switch does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA pressure switch is a simple thing with an important job: it senses whether there is pressure in the line and opens or closes a set of contacts accordingly. That signal is what tells the rest of the system it is safe to run. When the switch sticks or its contacts stop making, equipment either refuses to start or fails to shut down, and the fault is easy to misread as a bigger problem.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003ePressure switches from different makers look very similar. Read the number on the body of the one you are replacing and confirm it against 34-0019-C or 4037P.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48626492670164,"sku":"HQP-851-8007","price":24.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_708a28df-869f-42e3-bda1-847b85e6e2d3.jpg?v=1788710914"},{"product_id":"3-load-retrofit-control-system-without-cords","title":"Hydroquip BP7 Water Pro Series Control System, 4.0 kW, TP600, Three Load Retro-Fit Kit","description":"\u003cp\u003eThe Hydroquip 50-BP7-600-40-K is a Water Pro Series retro-fit control system built around the Balboa powered BP7 pack. It comes with a TP600 topside panel and a 4.0 kW heater, and is configured for three loads.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat a retro-fit kit is for\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSpa control systems eventually fail: a heater goes, a board cooks, or a discontinued topside leaves the spa with no way to control it. A retro-fit kit replaces the whole control platform with a current one instead of chasing parts for an obsolete pack, and brings a modern topside with it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThree loads and the topside\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThree load capacity covers the usual arrangement of a pump plus a blower or a second pump, alongside the heater. The TP600 panel is included, so the kit arrives with the interface the spa will be operated from rather than needing one sourced separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePlan the wiring\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis version ships without cords. Work out the connections you need before installation day, and have the work done by someone qualified to wire spa equipment.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48626858885332,"sku":"HQP-85-9911","price":579.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_9bf44179-4f29-46dd-9123-ea17ab4ab804.png?v=1788715922"},{"product_id":"hydro-quip-50-bp7-700-55-k-tp700-controller-5-5kw-bp7-retro-fit","title":"Hydro-Quip 50-BP7-700-55-K TP700 Controller 5.5KW BP7 Retro-Fit","description":"\u003cp\u003eThe Hydro-Quip 50-BP7-700-55-K is a Water Pro Series retro-fit kit, supplied as a complete control package rather than a loose board. It is powered by the Balboa BP7 control system and comes with a TP700 topside panel.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat you get\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe pack pairs the BP7 control with a 5.5KW heater and the TP700 topside, so the control side of the spa is replaced as one matched set. Buying it as a kit avoids the usual problem with piecemeal repairs, where a new board and an old topside will not talk to each other.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the genuine Hydro-Quip part 50-BP7-700-55-K. Retro-fit work means matching the pack to the spa plumbing, wiring and equipment already in place, so confirm the fit against your installation before ordering.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48627917324500,"sku":"HQP-85-1215","price":807.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_695a56ce-f57a-4df1-94de-8590dc9803de.png?v=1788729818"},{"product_id":"balboa-bp7-water-pro-series-control-system-5-5kw-tp600-topside-retro-fit-spa-control","title":"Hydro-Quip TP600 Controller 5.5kW BP7 Retro-Fit Kit","description":"\u003cp\u003eThis is the Hydro-Quip Water Pro Series spa control, part number 50-BP7-600-55-K, supplied as a retro-fit kit. It is built around the Balboa BP7 control system, carries a 5.5kW heater, and includes the TP600 topside panel.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat a retro-fit kit gives you\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe kit is meant for replacing a spa control that is already in place. Pack and topside come together under one part number, so the control side of the spa gets replaced as a matched set rather than assembled from pieces that then have to be made to talk to each other.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe pieces\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe BP7 is the Balboa control system doing the work inside. The TP600 is the panel the owner actually touches, mounted at the spa. The 5.5kW figure is the heater output in this configuration, and it is one of the specifications to check against what the spa was originally built around before ordering.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48627971522772,"sku":"HQP-85-1216","price":579.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_cc2ff304-9abb-48fe-9008-189553392667.png?v=1788732009"},{"product_id":"4kw-incoloy-m7-heater-element","title":"Hydroquip 4 kW Incoloy M7 Heater Element with Hardware, 240V","description":"\u003cp\u003eThe Hydroquip 12-0102-K is a 4 kW Incoloy heater element rated for 240 V, supplied with its mounting hardware. It is the replacement element for a spa heater assembly rather than a complete heater.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy elements fail\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe element is the part of a spa heater doing the actual work, and it lives in hot, chemically active water. Scale builds on it, corrosion works at it, and eventually it either opens circuit or shorts to the housing and trips the breaker. The housing, the unions and the sensors around it usually outlast several elements.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eMatch the rating to what came out. This element is 240 V and 4 kW, which is the common residential spa figure, but heater assemblies are also built in other ratings and fitting the wrong one gives you either a heater that never reaches temperature or one that overdraws the circuit.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48628833386708,"sku":"HQP-851-8005","price":42.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/12-0102-k-4kw-heater-element-w-hardware.jpg?v=1788753678"},{"product_id":"waterpro-50mg-120-240v-cd-ozone-generator","title":"HydroQuip Water Pro Ozonator Kit 120\/240V 50mg","description":"\u003cp\u003eThe HydroQuip Water Pro ozonator kit, part 34-2722-50-K, is a corona discharge ozone generator rated at 50 mg for use with a hot tub. It is built to work interchangeably on 120V or 240V, which takes the guesswork out of matching it to an existing pack.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is in the kit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe box holds the generator itself, a 6 foot power cord with a 4 pin Amp plug, 6 feet of 1\/4 inch by 3\/8 inch tubing, a check valve and an installation manual. That is everything the connection needs apart from the injector fitting already in the plumbing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe check valve is not optional\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOzone reaches the water through soft tubing, and tub water will siphon back down that tubing the moment pressure drops. The check valve in the kit is what stops it. Fit it, and mount the generator above the water line where the manual shows.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48628846723284,"sku":"HQP-85-1064","price":86.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/34-2722-50-k-waterpro-50mg-120240v-cd-ozone-generator.jpg?v=1788755235"},{"product_id":"5-5kw-titanium-m7-heater-element","title":"Hydro-Quip 5.5kW Titanium M7 Heater Element","description":"\u003cp\u003eThe Hydro-Quip 12-0100F-K is a titanium heater element rated 5.5 kW at 240 volts, supplied for M7 heater assemblies.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the element is the part that goes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe element is the one component in the heater that is submerged, energized and cycled every time the system calls for heat. Scale, low flow and out of range water chemistry all shorten its life. When a heater still runs its pump and its controls but never brings the water up, or trips protection as soon as it fires, the element is the first thing to test.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order and before you fit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCheck 12-0100F-K against the number on the element you are removing, and confirm the 5.5 kW and 240 volt ratings match the heater. Cut power at the breaker before the heater is opened; this is a 240 volt circuit.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48629084848340,"sku":"HQP-851-8028","price":54.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/12-0100f-k-55kw-titanium-m7-heater-element.jpg?v=1788759574"},{"product_id":"1-1-2-wow-circulation-pump-1hp-15hp-230v-0-6-amp","title":"HydroQuip 1-1\/2\" WOW Circulation Pump 1HP\/15HP 230V 0.6 Amp","description":"\u003cp\u003eThe HydroQuip 10-6154106 is a WOW circulation pump with 1-1\/2 inch connections, running on 230V and drawing 0.6 amp. It is built as a bath and whirlpool circulation pump rather than a pool filtration pump.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuilt to be left alone\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe WOW line was designed around reliability in a duty where the pump is buried in a cabinet and nobody is going to look at it again. It is compact, it goes in without a fight, and the self draining volute means water is not left standing in the housing after every cycle. That is a small design decision that matters a lot over years of use.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck the numbers before you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm the 1-1\/2 inch connection size against your plumbing and confirm you have 230V available at the pump. The horsepower is listed by the manufacturer as 1HP\/15HP, which is carried here exactly as given.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48629290238164,"sku":"HQP-10-1019","price":302.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4e5667d0-7b50-4f8f-9074-3d151630bfc4.png?v=1788761999"},{"product_id":"4kw-titanium-m7-heater-element","title":"Hydroquip 4kW Titanium M7 Heater Element","description":"\u003cp\u003eThis is the Hydroquip 12-0102F-K heater element, a titanium element rated 240 volts at 4 kW for M7 heater assemblies.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy titanium\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe element is the part in direct contact with the water, and it is where poor chemistry shows up first. Titanium holds up where a standard element scales, pits and eventually opens. Rating matters as much as fit here: two elements can look identical and carry different voltage and wattage, so 12-0102F-K is the number to order against.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore fitting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn element rarely fails for no reason. Restricted flow, a heater run dry, or water well out of balance will take out the replacement as quickly as it took out the original, so it is worth finding the cause while the housing is open.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48629510602964,"sku":"HQP-851-8006","price":56.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/12-0102f-k-4kw-titanium-m7-heater-element.jpg?v=1788765988"},{"product_id":"spdt-air-switch-25a","title":"Hydroquip SPDT Air Switch, 25A","description":"\u003cp\u003eHydroquip 34-0002 is a replacement SPDT air switch rated at 25 amps. It is the switch an air button actually operates inside the equipment pack.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow the circuit works\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eNothing electrical runs out to the button on the deck. Pressing it sends a pulse of air down a length of small bore tubing to this switch, and the switch handles the load. That arrangement is why an air button can sit within reach of the water in the first place.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSingle pole double throw\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSPDT means one common contact that connects to one of two outputs. It is worth checking the configuration of the switch you are replacing, because latching and momentary versions and different contact arrangements are used across equipment packs.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA dead button is not always a dead switch. Trace the air tubing first and look for cracks, kinks and water sitting in the line. If the tubing is sound and the button still does nothing, the switch is the next thing to change.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48629536751828,"sku":"HQP-851-8032","price":15.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_9126904d-1821-4df5-9b7e-d13025978008.jpg?v=1788766317"},{"product_id":"5-5kw-incoloy-m7-heater-element","title":"Hydroquip 5.5kW RHS Heater Element with Hardware","description":"\u003cp\u003eThe Hydroquip 12-0100-K is a 5.5kW flow through heater element supplied with its hardware, designed to fit RHS heaters. It is a new OEM part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow a flow through element works\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe element sits directly in the water path inside the heater tube, so water heats as it is pumped past. That design is efficient and compact, but it means the element is exposed to whatever the water carries. Scale, low flow and aggressive chemistry all shorten its life.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSigns the element has gone\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA heater that trips its breaker, will not raise temperature, or shows a ground fault on the heat circuit is usually pointing at the element. Before fitting a new one, look for the reason the old one failed: heavy scale on the removed element or a restricted flow path will take the replacement out the same way.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48633767067860,"sku":"HQP-851-8004","price":39.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_a5d1408c-a68c-405a-8b05-c28ae9a8e149.jpg?v=1788814871"},{"product_id":"14x-25-gecko-4p3w-w-m-t-hl-sensor","title":"Hydro-Quip Gecko 4-Pole 3 Wire Hi Limit Sensor with 1\/4 Inch Bulb","description":"\u003cp\u003eThe Hydro-Quip 34-0201 is a hi limit sensor for Gecko spa controls. It uses the Gecko 4-pole 3 wire connector, has a 1\/4 inch sensing bulb and a 14 inch lead.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it protects\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe hi limit is the safety sensor at the heater. It is not the one that holds your set temperature; its job is to notice when the water at the heater has gone past a safe point and shut the heater down before anything is damaged or anyone is scalded. Because it is a safety device, a spa will refuse to heat rather than run without a working one.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe symptom that leads here\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRepeated overheat or hi limit faults on a spa whose water is plainly not hot. A sensor that has drifted out of range or failed open reports a temperature that is not real, and the controller does the safe thing and locks the heater out.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eGetting the right one\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe connector is what matters most. Count the poles and wires on the sensor you are removing and confirm it is the Gecko 4-pole 3 wire style before ordering.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48634165756116,"sku":"HQP-851-9029","price":74.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/34-0201-14x25-gecko-4p3w-wmt-hl-sensor.jpg?v=1788826041"},{"product_id":"1-amp-pressure-switch","title":"HydroQuip 1 Amp Pressure Switch","description":"\u003cp\u003eThis is the HydroQuip 1 amp pressure switch, part number 34-0178. It is the direct replacement for the original switch, ordered by the factory number so there is no guessing about which version you are getting.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat a pressure switch does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA pressure switch watches water pressure and makes or breaks an electrical circuit accordingly. Only when there is pressure in the line does the switch close and let the equipment it protects run. When pressure drops away, the switch opens again. That is what keeps things from firing up dry.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSwitches wear out. A contact that no longer closes leaves the equipment dead even though everything else is working, and a switch that sticks or chatters makes it cut in and out. If you have confirmed the system has proper flow and it still will not run reliably, the switch is the part to change.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48634503397588,"sku":"HQP-851-8008","price":47.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4b804038-7197-4357-a8ec-6dba345a202a.jpg?v=1788833034"},{"product_id":"2-ridged-gasket","title":"Hydroquip 2\" Ridged Gasket","description":"\u003cp\u003eHydroquip 60-0015 is a rubber ridged gasket for standard 2 inch unions. It is a replacement seal that turns up in several standard 2 inch unions and can be used with unions from a number of different manufacturers, which is what makes it worth keeping on the shelf.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFlat one side, ridged the other\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe gasket is flat on one face and carries a raised o-ring style extension on the other. That shape is the whole point: the flat side beds against one union half while the raised ridge concentrates the clamping load into a narrow band on the other, which is what makes the joint seal at low tightening force. It also means the gasket has a right way round, so note the orientation of the old one as it comes out.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDimensions to check\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOutside diameter is 2-15\/16 inch, inside diameter is 2-1\/8 inch, and thickness is 3\/32 inch across the flat section or 3\/16 inch measured over the ridge. Compare those against the gasket you are replacing, because a union that looks like a 2 inch union is not always dimensionally identical. A seal that is old, hard or has taken a permanent set will not recover, and no amount of tightening will make it hold.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48635042562260,"sku":"HQP-801-1000","price":8.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_488ec92b-ab43-4789-aa22-6332e32d9a29.jpg?v=1788840487"},{"product_id":"hydroquip-bcs-55-series-baptismal-equipment-5-5kw-heater-240v-bcs-55-3w","title":"Hydro-Quip BCS-55 Series Baptismal Equipment, 5.5kW Heater, 240V, BHS-55-3W","description":"\u003cp\u003eThe Hydro-Quip BCS-55 series is a packaged equipment system for baptismal pools. This is the BHS-55-3W, with a 5.5kW heater on 240 volt three wire service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the package covers\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRather than assembling a heater, a control and safety devices separately, the BCS-55 arrives as one unit. It includes a high limit and a pressure switch, an air switch for control, a pump receptacle and a tailpiece connection. Total draw is 23 amps at 50 or 60 Hz.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAir switch control\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn air switch operates the system through a column of air rather than a wire, which keeps line voltage away from the person pressing the button. That is the normal approach around water and it is why these packages are built this way.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting it in\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe unit itself is 13 inches high, 6.5 inches wide and 5.5 inches deep. Hydro-Quip asks for a minimum of 26 inches high by 7 inches wide by 6 inches deep, which allows room to reach the connections and service the unit later. Confirm the service is three wire 240 volt before ordering.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48645965414612,"sku":"PSU-176703","price":333.58,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/176703_0_2019103015813.jpg?v=1788975276"},{"product_id":"hydroquip-baptismal-equipment-5-5kw-heating-and-control-system-120-240v-bes6000","title":"Hydro-Quip Baptismal Equipment 5.5 kW Heating and Control System, 120\/240V, BES6000","description":"\u003cp\u003eThe Hydro-Quip BES6000 is a packaged baptismal heating and control system with a 5.5 kW heater, running on 120\/240 volt service. It handles the heating and the control of baptismal equipment as one unit rather than as separately assembled parts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eElectrical\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHydro-Quip specifies four wire, 60 Hz service. The BES6000 and the BES6000T are both listed at a total amp draw of 36A with a 50 amp circuit breaker. That is a dedicated circuit, and it is worth confirming the panel has room before the system arrives.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSpace\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe cabinet for the 5.5 kW models is listed at 13 inches high by 27 inches wide by 15 inches deep. Hydro-Quip separately gives a minimum space required of 14 inches high by 26 inches wide by 16 inches deep. Those two figures disagree on width, so plan the alcove around the larger of the two and leave room to get a hand behind the unit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe larger model\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIf 5.5 kW is not enough for the volume of water, Hydro-Quip lists an 11 kW pair, the BES6005 and BES6005T. Those draw 56A on a 70 amp breaker and sit in a slightly wider cabinet, 13 inches high by 29 inches wide by 15 inches deep.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48645968494804,"sku":"PSU-155296","price":816.64,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/155296_0_20193241283.jpg?v=1788975354"},{"product_id":"hydroquip-portable-baptismal-equipment-4-0kw-heater-and-pump-240v-pbes6040","title":"Hydro-Quip Portable Baptismal Equipment, 4.0 kW Heater and Pump, 240V, PBES6040","description":"\u003cp\u003eThe Hydro-Quip PBES6040 is a portable baptismal package that puts the heater and the circulation pump in one cabinet. It is rated at 4.0 kW on a 240 volt supply and ships with an installation kit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePower and circuit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe package is single phase and works on 50 or 60 Hz. Total draw is listed at 20 amps with a 30 amp circuit breaker specified, so the circuit needs planning before the first service rather than on the day. The pump that ships with it is listed at 1\/6 HP, 120V, base mounted.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePortable by design\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAt 12.5 inches high, 13 inches wide and 9 inches deep the cabinet is small enough to move and store between uses, which is the point of a portable baptistry setup. Heat is applied when the tank is filled and the equipment goes back into storage afterward.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48646284214484,"sku":"PSU-176929","price":710.78,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/176929_0_20191030151214.jpg?v=1788987748"},{"product_id":"hydroquip-inmersion-series-baptistry-heater-6-0kw-240v-30-amp-gfci-bis-60-240-bis-60-240-gf","title":"Hydro-Quip Immersion Series Baptistry Heater, 6.0 kW 240V 30 Amp GFCI, BIS-60-240-GF","description":"\u003cp\u003eThe Hydro-Quip Immersion Series BIS-60-240-GF is a baptistry heater rated at 6.0 kW on a 240 volt supply, with a 30 amp GFCI. It is the built in heater for a permanent baptistry rather than a portable package.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe electrical side\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is a 240 volt appliance on a 3-wire supply with a 30 amp GFCI, so it needs a dedicated circuit run by an electrician. That is worth settling before the unit arrives, because the circuit, not the heater, is usually what holds up an install.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSizing and space\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e6.0 kW is the higher output in the range, which matters when a tank has to come up to temperature between a Saturday setup and a Sunday service rather than over several days. The cabinet is listed at 46 inches high by 18 inches wide, so confirm the wall or closet space where it will live.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48646284509396,"sku":"PSU-173630","price":560.85,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/173630_0_201942293521.jpg?v=1788987770"},{"product_id":"hydroquip-baptismal-equipment-11kw-heating-and-control-system-bes6005","title":"Hydro-Quip BES6005 Baptismal Heating and Control System, 11kW","description":"\u003cp\u003eThe Hydro-Quip BES6005 is the 11kW baptismal heating and control system from the BES6000 series. Heater and controls arrive as one unit, so a single enclosure handles bringing the water up to temperature and holding it there.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA baptistry is filled and heated on a schedule rather than run continuously like a pool, which means the equipment has to raise a modest volume of water reliably and then be left alone between uses. The 11kW output is the larger of the two in the series, and the one to specify when the tub is bigger or the fill window is short.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSpace and mounting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHydro-Quip gives a minimum space requirement of 14\"H x 26\"W x 16\"D and lists the 11kW units at 13\"H x 29\"W x 15\"D. Those two figures do not agree on width, so measure the space you have against both before you settle on a location.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eElectrical\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe system runs on a 4 wire service at 60 Hz. Amp draw and breaker size differ across the models in the series, so this is a job to hand to a licensed electrician working from the Hydro-Quip installation sheet for the BES6005 rather than from a general figure.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48646289391828,"sku":"PSU-155300","price":870.24,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/155300_0_201932412851.jpg?v=1788987784"},{"product_id":"hydroquip-pbes6000-series-portable-baptismal-equipment-1-0kw-heater-and-pump-120v-pbes6010-pbes-6010","title":"Hydro-Quip PBES6010 Portable Baptismal Equipment, 1.0kW Heater and Pump, 120V","description":"\u003cp\u003eThe Hydro-Quip PBES-6010 is the 1.0kW, 120 volt model in the PBES6000 series of portable baptismal equipment. It combines a heater and a 1\/6 HP base mounted pump in a single compact unit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHeater and circulation in one box\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe pump moves the water so the heater does not simply cook a layer at the element and leave the rest cold, and having both in one enclosure keeps the setup to a single piece of equipment and one supply. At 12.5\"H x 13\"W x 9\"D it sits beside the tub rather than needing a plant room.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eElectrical\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt runs on 120V single phase at 50\/60 Hz. Hydro-Quip lists a total amp draw of 12.5A and a 15 amp circuit breaker, which does not leave much room on a circuit that is doing anything else. Have an electrician confirm what is feeding the location before the first fill.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOrdering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eYou will see this unit written as PBES6010 and as PBES-6010. They are the same part.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48646289490132,"sku":"PSU-69769","price":636.49,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/69769_0_20191030133830.jpg?v=1788987795"},{"product_id":"hydroquip-bes-55-series-baptismal-equipment-5-5kw-heater-and-pump-120-208-240v-bes-55","title":"Hydro-Quip BES-55 Series Baptismal Equipment, 5.5kW Heater and Pump, 120\/208\/240V","description":"\u003cp\u003eThe Hydro-Quip BES-55 is a baptismal equipment pack that combines a 5.5kW heater and a pump in one unit, wired for 120\/208\/240 volt single phase service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOne unit instead of two installs\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHeating a baptistry usually means finding room for a heater, a pump and the plumbing between them. The BES-55 puts that into a single 29 by 15 by 9 inch package with an 18 amp total draw, a heater indicator light and a bonding lug and wire, and it ships with an installation kit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePlanning the install\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAllow more than the cabinet footprint. Hydro-Quip publishes a minimum space requirement of 36 inches high by 16 inches wide by 10 inches deep. Electrically it is a single phase, 4-wire connection at 50\/60 Hz, and the 18 amp figure is what the circuit should be sized around. Have the connection made by a licensed electrician to local code.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48646298829012,"sku":"PSU-176897","price":654.89,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/176897_0_2019102915631.jpg?v=1788987868"},{"product_id":"hydroquip-baptismal-equipment-11kw-heating-and-control-system-with-7-day-timer-bes6005t","title":"Hydro-Quip Baptismal 11kW Heating and Control System with 7 Day Timer, BES6005T","description":"\u003cp\u003eThe Hydro-Quip BES6005T is a packaged heating and control system for baptismal tanks. It combines an 11kW heater with the control gear and a seven day timer in a single cabinet.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe timer is the point\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA baptistry sits cold most of the week and needs to be warm on a schedule. The seven day timer lets the system be programmed to bring the tank up ahead of a service without anyone remembering to switch it on. The BES6005 is the same 11kW unit without the timer, so the T suffix is what to look for.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eElectrical requirements\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is a substantial electrical load. The system draws 56 amps total and calls for a 70 amp circuit breaker on a 4 wire service at 60 Hz. The circuit should be run and terminated by a licensed electrician, and the supply confirmed before the equipment is ordered.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSpace and mounting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe 11kW cabinet measures 13 inches high, 29 inches wide and 15 inches deep. Plan the location with enough clearance for the conduit run and for opening the cabinet later for service.\u003c\/p\u003e","brand":"Hydro-Quip","offers":[{"title":"Default Title","offer_id":48646304039124,"sku":"PSU-155303","price":681.2,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/155303_0_2019324121035.jpg?v=1788987956"}],"url":"https:\/\/www.activepoolsupply.com\/collections\/hydro-quip.oembed","provider":"Active Pool Supply","version":"1.0","type":"link"}