{"title":"Jandy Parts","description":"\u003cp\u003eJandy parts at Active Pool Supply, genuine OEM and quality aftermarket.\u003c\/p\u003e","products":[{"product_id":"zodiac-r0693900-truclear-pcb-replacement-assembly-for-jandy-pro-series-chlorine-generator","title":"Jandy TruClear PCB Cell Replacement Assembly for Pro Series Chlorine Generator, R0693900","description":"\u003cp\u003eThe Jandy R0693900 is the genuine replacement PCB cell assembly for the Jandy Pro Series TruClear salt chlorine generator. It is the part to order when a TruClear system that is otherwise healthy stops producing chlorine.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eGenuine part, direct fit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the assembly Jandy specifies for the TruClear, not a generic equivalent. It replaces a worn or faulty cell assembly directly, without changes to the plumbing or the power center.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSalt cells wear with use. If salt level, stabilizer and water balance are correct, the cell is clean and the system still cannot hold a chlorine residual, the cell assembly is the usual cause. The TruClear installation and operation manual covers the checks to run before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm your system is a Pro Series TruClear. Jandy states that its limited warranty does not apply to Jandy branded products bought through the internet or other e-commerce platforms, so this part is sold without that warranty.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48620696895700,"sku":"JDY-45-9879","price":754.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default.jpg?v=1788573176"},{"product_id":"jandy-r0984100-pcb-large-backboard-with-screws","title":"Jandy AquaPure Power Interface PCB, Large Backboard with Screws, R0984100","description":"\u003cp\u003eThe Jandy R0984100 is the genuine power interface PCB for AquaPure salt chlorine generators: the large backboard that sits in the control box, supplied with its mounting screws. It replaces the earlier R0467600.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe power interface board carries power to the rest of the AquaPure control system. When an AquaPure will not power up, or powers up with no output and the cell and user interface check out, this board is the usual suspect.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOld number, new part\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIf your control box has a board marked R0467600, this R0984100 is Jandy's current replacement for it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the power interface board, not the user interface PCB, which is a separate part. Jandy states that its limited warranty does not apply to Jandy branded products bought through the internet or other e-commerce platforms.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48620700369108,"sku":"JDY-301-7237","price":239.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_02fd3b3c-97c5-43b5-807b-8b1b168c0680.jpg?v=1788573186"},{"product_id":"port-sensor-kit-for-3-port-cell-with-16-cable","title":"Jandy Port Sensor Kit for 3 Port Cell with 16' Cable, R0452500","description":"\u003cp\u003eThe Jandy R0452500 is the replacement port sensor kit for 3 port AquaPure cells on Zodiac Jandy PureLink APURE1400 and APURE700 systems. It is the new style sensor with a 16 ft cable, and it comes with a new interface module and the o-rings for the install.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOld style or new style, this is the part\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe new style sensor is a direct replacement for the older style, so it does not matter which version your system was built with. The interface module in the kit is what makes the newer sensor work in place of the old one, which is why it ships as a kit rather than a bare sensor.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCheck that your cell is the 3 port type and your system is a PureLink APURE1400 or APURE700. The cable is 16 ft, the standard PureLink length.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624540516564,"sku":"JDY-451-3801","price":299.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_e4794f77-0085-42fd-b449-5869fa5bc189.jpg?v=1788643076"},{"product_id":"aqualink-aquapure-cell-kit-for-pools-up-to-40-000-gallons-with-16-cable","title":"Jandy AquaLink AquaPure 3-Port 14-Blade Replacement Salt Cell Kit, 40K Gallons, 16' Cable, PLC1400","description":"\u003cp\u003eThe Jandy PLC1400 is the Pro Series AquaPure replacement cell kit for pools up to 40,000 gallons. It is the 3 port, 14 blade cell with a 16 ft DC cable, and the kit includes the slotted sensor, sensor tee, pressure switch, flow sensor, two universal unions and o-rings.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe replacement for 2 port cells\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis kit replaces all of the older 2 port AquaPure cells. Because the 3 port design puts the sensor in its own tee, the tee and sensor are in the box rather than being a separate order. The unions are 2 in. slip by 2-1\/2 in. spigot, so they fit either pipe size without adapters.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow it works\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe AquaPure system generates chlorine from the salt dissolved in the pool water. Once that chlorine has sanitized the water it converts back to salt, and the cycle repeats. The result is a steady chlorine level without handling liquid or tablet chlorine.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe 16 ft cable is the only length offered. Confirm your system is an AquaPure 1400 class unit for pools up to 40,000 gallons.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624540647636,"sku":"JDY-45-1405","price":1395.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4896dd51-06a1-4933-b2f8-975ee56d4a96.png?v=1788643079"},{"product_id":"nature2-fusion-soft-1400-cell-kit-40k-gallon","title":"Zodiac Nature2 Fusion Soft 1400 Cell Kit for 40,000-Gallon Pools, R0503000","description":"\u003cp\u003eThe Zodiac R0503000 is the replacement cell kit for the Nature2 Fusion Soft 1400, the combined salt chlorine generator and mineral sanitizer for pools up to 40,000 gallons. The kit includes the Nature2 Fusion Soft cell, a replacement electrode and an o-ring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow Fusion Soft works\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe cell generates chlorine from salt in the pool water while a Nature2 mineral cartridge in the same housing lets the pool run at a lower chlorine level. Nature2 has been the leading mineral based system for over 18 years, installed in more than 300,000 pools and spas.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOperating limits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe cell runs between 30 and 120 gpm at no more than 50 psi, with a recommended salt level of 3,000 ppm.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is not in the box\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe mineral cartridge is sold separately: a DuoClear 45 or Nature2 Fusion 45, part W28002, for pools to 40,000 gallons. The DC cord is also separate. The Fusion Soft takes either a 16 ft or a 25 ft cord, and both are available.\u003c\/p\u003e","brand":"Nature2","offers":[{"title":"Default Title","offer_id":48624543629524,"sku":"JDY-45-1408","price":1179.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c92b9851-aaee-443e-a030-4e9ac08c4016.jpg?v=1788643132"},{"product_id":"jandy-bwvl-mpv-80-2-side-mount-multi-port-valve-with-unions","title":"Jandy 2\" Side Mount Multi-Port Valve with Unions for DEV48\/60, JS60-SM or JS100-SM, BWVL-MPV-80","description":"\u003cp\u003eThe Jandy BWVL-MPV-80 is the 2 in. side mount multiport valve fitted to Jandy DEV48 and DEV60 DE filters and to the JS60-SM and JS100-SM side mount sand filters. It is supplied with its unions, so it couples straight to the filter tank.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSix positions on one handle\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eEveryday filtering, backwash, rinse and the remaining service modes are all selected from the single handle, which is what makes a multiport the easiest way to run a DE or sand filter through a cleaning cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMolded ABS\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe body is molded ABS: rigid, corrosion free and suited to a valve that spends its life outdoors with water in it. Ports are 2 in. to match the plumbing on these filters. This is the genuine Jandy part.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624548348116,"sku":"TLD-06-134","price":327.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6ff46842-89b0-40d6-aee1-39b347b1f1d0.jpg?v=1788643242"},{"product_id":"tank-bottom-assembly","title":"Jandy Replacement Bottom Tank Assembly for CL \u0026 DEV Model Filters, R0466500","description":"\u003cp\u003eThe Jandy R0466500 is the lower tank half for CL series cartridge filters and DEV series DE filters, supplied as a complete assembly rather than a bare shell. The tank bottom comes with its bulkhead fitting, unions with o-rings, outlet elbow, tank o-ring and tank retaining ring, so a cracked or leaking lower tank can be swapped without chasing down the small parts separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat you get\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eEverything that lives below the clamp ring: the molded tank bottom, the bulkhead fitting, both unions with their o-rings, the outlet elbow, the large tank o-ring that seals the two halves, and the retaining ring. The existing tank top, internals and clamp carry over.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOlder DEL and CV tanks\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis assembly can also replace the bottom on a DEL DE filter or a CV cartridge filter, but not as a straight swap. On a DEL the drain is on the side rather than the back, the plumbing unions must be replaced because the bulkhead fittings are different, and the multiport valve has to be replaced as well because the union threads do not match. On a CV with the inlet on one side and the outlet on the other, the plumbing has to be brought around so that both connect at the front of the tank, inlet at the bottom port and outlet at the top port. The unions in the box are there for that work.\u003c\/p\u003e\u003cp\u003eOn a current CL or DEV filter, none of that applies: set the new bottom in place, seat the o-ring, drop the internals back in and clamp the top on.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624549822676,"sku":"TLD-051-5048","price":768.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4b59065b-00d7-4f71-a711-cd3ca5021b4b.jpg?v=1788642919"},{"product_id":"lid-lock-ring-assembly-w-seal-phpf-phpm","title":"Jandy Lid \u0026 Lock-Ring Assembly with Seal, PHPF\/PHPM, R0448800","description":"\u003cp\u003eThe Jandy R0448800 is the genuine replacement lid and lock ring assembly for Plus HP PHPF and PHPM pumps. It comes as a kit of three parts: the clear trap lid, the black lock ring assembly and the lid o-ring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich pumps\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt is listed for the Plus HP PHPF and PHPM, and the same assembly is used on the MaxHP MHPM and WaterFeature WFTR series. The lid is 7-13\/16 in. across, clear plastic, with a four tab twist lock.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOld part numbers\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis kit replaces A0578200 and A0578100. If you look at your existing clear lid you will find A0578100 stamped into it. That lid is not sold on its own, only as part of this kit.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624831496404,"sku":"TLD-101-2012","price":74.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_f6c7ccb9-6d01-4c75-8a20-c1b77e616413.jpg?v=1788643124"},{"product_id":"pro-series-cell-kit-3-port-1400-replacement-kit","title":"Jandy AquaPure PureLink 3-Port 14-Blade 1400 Replacement Salt Cell Kit for 40,000 Gallon Pools, R0452400","description":"\u003cp\u003eThe Jandy R0452400 is the 14-blade, 3-port replacement salt cell for Jandy AquaPure and PureLink chlorine generators, the 1400 size rated for residential pools up to 40,000 gallons. It produces up to 1.25 lb of chlorine in 24 hours (567 g).\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat Jandy lists for this part\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eJandy's AquaPure and PureLink manual lists R0452400 as the 14-blade cell for the 3-port cell: the cell assembly, three #2-231 O-rings and a 16 ft black DC power cord. The universal union, tailpiece and plug kit is a separate Jandy part, R0452100, and the 3-port flow, temperature and salinity sensor is R0452500 (16 ft cable) or R0476400 (25 ft cable). Confirm what your pad already has before you order.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe 1400 cell is the one Jandy specifies for pools up to 40,000 gallons. Jandy's smaller 700 model is rated for pools up to 12,000 gallons, so size up to the 1400 for larger pools. PureLink power centers use a PLC700 or PLC1400 cell kit, and the power interface board is set to the 1400 model by default.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCell care\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe control system cleans the cell plates about every 3 hours by reversing the polarity of the current, and chlorine is still produced in reverse. Jandy recommends checking a new cell monthly for several months, then removing it for inspection at least twice a year. Scale on the plates is cleaned with a hose or the acid wash steps in the manual.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624832479444,"sku":"JDY-45-1407","price":1229.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_bc7e0100-a4e1-4fb5-974f-f2d7917f6692.jpg?v=1788643227"},{"product_id":"zodiac-r0663800-cover-assembly-with-user-interface-for-jandy-pro-series-truclear-chlorine-generating-system","title":"Jandy Cover Assembly with User Interface for TruClear Chlorine Generating System, R0663800","description":"\u003cp\u003eThe Jandy R0663800 is the replacement cover assembly for the Pro Series TruClear chlorine generating system, with the user interface built into it. On the TruClear the display and buttons live in the top cover of the power center, so when the readout fades or the buttons stop responding, the cover and interface are replaced together as this one part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eGenuine part\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eR0663800 is the OEM part made by Zodiac for Jandy. It is the same assembly that ships on a new TruClear, so fit and function match the original.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm your system is the Pro Series TruClear, not the Jandy AquaPure, which uses a different power center. If the display works but chlorine output has dropped, check the cell and the power pack before replacing the cover.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624870064340,"sku":"JDY-45-9884","price":419.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_10b9370e-03f5-45b8-b4e6-a3a325620a5c.png?v=1788647587"},{"product_id":"16-aquapure-cell-cord","title":"Jandy 16' AquaPure PureLink DC Cell Cord, R0402800","description":"\u003cp\u003eThe Jandy R0402800 is the 16 ft DC cord for the AquaPure and PureLink 3-port salt cell. It runs from the power center to the cell and is the part to replace when the original cord is cut, chewed, cracked or corroded at the connector.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt is the Zodiac \/ Jandy OEM cord for the 3-port cell, so it swaps for the original without adapting anything. If 16 ft is more reach than your pad needs, an 8 ft AquaPure DC cord is available separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNote\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the DC power cord only. The sensor cable for the 3-port cell is a separate kit.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624873275604,"sku":"JDY-451-2800","price":24.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_21cf2db8-c661-427d-a83d-10e960759c4c.jpg?v=1788647903"},{"product_id":"gauge-air-release-assembly","title":"Jandy Genuine Replacement Gauge with Air Release Assembly, R0357200","description":"\u003cp\u003eThe Jandy R0357200 is the genuine pressure gauge and air release assembly fitted to Jandy cartridge, sand and DE filters. The gauge tells you when the filter needs cleaning; the air release bleeds trapped air from the top of the tank after the lid has been off. This assembly replaces both together.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCV340, CV460 and CV580 and CL340, CL460 and CL580 cartridge filters, JS60-SM and JS100-SM sand filters, and DEV48, DEV60, DEL48 and DEL60 DE filters.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy it matters\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA gauge that sticks, reads high, or never returns to zero leaves you guessing about filter pressure, and a guess usually means the filter runs dirty too long. The R0357200 has a clear, easy to read dial and corrosion resistant construction, so it keeps giving a straight answer season after season. Wrap the threads with PTFE tape, thread it in hand tight plus a modest turn, and do not overtighten.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624873570516,"sku":"TLD-101-6000","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_891aa019-6afb-4c85-a2e0-ca7fc6cd9ced.jpg?v=1788647946"},{"product_id":"pump-body-shpf-shpm","title":"Jandy Pump Body for Stealth SHPF\/SHPM Pumps, R0445601","description":"\u003cp\u003eThe Jandy R0445601 is the genuine pump body for the Stealth SHPF and SHPM pumps, and it is shared by the WaterFall SWF series and the ePump JEP variable speed pump. It is a unibody housing, meaning the strainer trap and the volute are one molded piece, so a crack in either means replacing this part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eConnections\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBoth suction and discharge are male buttress thread, the same as the original, so the existing Jandy unions thread straight back on without cutting pipe. The trap takes the standard four tab twist lock lid with an 8-13\/16 in. outside diameter.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is not in the box\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe drain plugs are not included; they are Jandy part R0446000. The lid and locking ring, strainer basket, seal plate and motor all transfer from your existing pump. Plan on new o-rings while everything is apart.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624873636052,"sku":"TLD-101-2008","price":381.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_71d40024-1614-4819-ba38-436a839f5889.jpg?v=1788647955"},{"product_id":"tank-top-cl580-del60","title":"Jandy Tank Top CL580\/DEL60, R0357300","description":"\u003cp\u003eThe Jandy R0357300 is the replacement tank top for the CL580 cartridge filter and the DEL60 D.E. filter. It is the genuine Jandy part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSpecial order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is typically a special order item with limited quantities, so plan for a longer lead time than a stocked part. It replaces the upper half of the filter tank when the original is cracked or damaged, without replacing the whole filter.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck before ordering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm your filter is a CL580 or DEL60 from the model plate. The bottom tank assembly and the tank body o-ring are separate parts; if the o-ring is old, it is worth replacing at the same time.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624874160340,"sku":"TLD-051-5042","price":601.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_d2e1af41-c29a-44ed-a00f-3a82615600c9.jpg?v=1788648015"},{"product_id":"r0462400-filter-cartridge-element-cs200","title":"Jandy Genuine OEM Filter Cartridge Element for CS200 Filter, R0462400","description":"\u003cp\u003eThe Jandy R0462400 is the genuine replacement cartridge element for the Jandy CS200 cartridge filter. It is the element the filter shipped with, so pleat count, end caps and fit match the tank exactly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e33 in. long, 8-7\/8 in. outside diameter, 4 in. inside diameter. If you are replacing an element without the original box, those three numbers against your old cartridge confirm you have the right one.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCleaning versus replacing\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA cartridge lasts several seasons if it is hosed off when the pressure rises and soaked in a cartridge cleaner once or twice a year to strip oils and scale that hosing leaves behind. When pressure stays high after a proper clean, or the pleats are torn, frayed or starting to collapse, it is time for a new element. Swapping it is a matter of opening the filter, lifting out the old one and setting this one in.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624877174996,"sku":"TLD-051-1902","price":276.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_502a564f-c6d3-40be-985e-7b97e4d1a5ce.jpg?v=1788648503"},{"product_id":"cell-kit-apure700-3-port-with-cord","title":"Jandy AquaPure PureLink 3-Port 7-Blade Replacement Cell Kit, R0452300","description":"\u003cp\u003eThe Jandy R0452300 is the replacement cell kit for AquaPure PureLink 3-port systems using the 7-blade APURE700 cell. It comes with the cell, a new o-ring and a 16 ft DC cord, which covers the parts that normally wear together.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is and is not included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIn the box: the 7-blade 3-port cell, the cell o-ring and the 16 ft DC cord. Not in the box: the tri-sensor. If your existing sensor is in good shape it carries over; if not, the 3 port sensor kit with a 16 ft cable is a separate item.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eChoosing between the 700 and the 1400\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eJandy makes the PureLink 3-port cell in two sizes. This is the 7-blade 700. The 14-blade 1400 is rated for pools up to 40,000 gallons. Match the replacement to the cell your system was built with rather than sizing up or down.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624877568212,"sku":"JDY-45-1406","price":913.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4ea89f70-f4cc-4f32-8e31-5d31354b52f8.jpg?v=1788648558"},{"product_id":"light-engine-pcb-large-led-light-with-light-shaping-diverge-120v","title":"Jandy Light Engine PCB Large LED Light with Light Shaping Diverge 120V, R0739400","description":"\u003cp\u003eThe Jandy R0739400 is a light engine PCB for the large Jandy LED pool and spa light with the light shaping diverge optic, 120V. The light engine is the circuit board that carries the LEDs, so replacing it restores a dead or failing fixture without replacing the whole light.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMatch three things\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eJandy makes light engines for the small and large LED lights, and the large light comes in 12V and 120V versions. Jandy's replacement kit instructions list the large LED light engine with the light shaping diverger as separate 12V and 120V parts. Confirm the large size, the diverge optic and 120V against your fixture before you order.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow Jandy replaces it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSwitch off the main breaker for the light circuit first. Jandy's instructions have you take the light out of the pool wall, which can be done under water without lowering the water level. Inside the fixture you remove the three nuts and washers, unplug the quick disconnect terminals, lift out the old board, and fit the new one with two nylon washers and two nuts torqued to 9 in-lbs. On a 120V large light the white wire goes to terminal J2 and the black wire to J3.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you reassemble\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eJandy says to install a new lens gasket whenever the light is taken apart. The work should be done by a technician qualified in pool and spa electrical installation.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624879141076,"sku":"JDY-301-0824","price":1019.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b771d9fd-9350-4286-98d9-6f9127a53924.jpg?v=1788648688"},{"product_id":"pump-housing-body","title":"Jandy Pump Housing Body for FHPM FloPro \u0026 VS FloPro, R0479800","description":"\u003cp\u003eThe Jandy R0479800 is the genuine replacement pump housing body for the FloPro FHPM series and the VS FloPro. It is the wet end shell that holds the strainer basket and carries the suction and discharge connections, and it is the part to order when a housing has frozen, cracked or started leaking at the seams.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt fits the single speed FHPM models from 0.75 through 2.5 HP and the variable speed VS FloPro. Your existing motor and internal parts transfer over.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is not included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the housing only. The pump basket, lid with lock ring, lid o-ring, diffuser and the 2 in. tailpiece o-rings and union nuts are separate parts. If any of them are worn, this is a convenient time to replace them.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624879468756,"sku":"TLD-101-2045","price":249.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_7f5ebc54-7cf5-4744-b736-e9b54e257563.jpg?v=1788648722"},{"product_id":"top-housing-assembly-cs100-cs150","title":"Jandy Top Housing Assembly CS100, CS150, R0461900","description":"\u003cp\u003eThe Jandy R0461900 is the gray top housing for CS100 and CS150 cartridge filters, the upper half of the tank that lifts off to reach the cartridge. It is the genuine Jandy part, made to the original dimensions so it seats and seals against the bottom tank exactly as the factory housing did.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA top housing usually needs replacing after a crack, a chip around the sealing edge, or long sun exposure that has left the plastic brittle. Swapping the housing is far cheaper than a new filter and keeps the rest of the CS unit in service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCheck the filter label for CS100 or CS150. The housing ships on its own; the 100 sq ft and 150 sq ft cartridges are separate parts, and a filter that is being opened up anyway is a convenient time to fit a new one.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624879861972,"sku":"TLD-051-1900","price":331.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_62567a69-ee84-4329-a094-a91c1f2e9ed1.jpg?v=1788648793"},{"product_id":"jandy-r0501300-complete-grid-assembly-dev-del-48-sqft","title":"Jandy Complete Grid Assembly for DEV\/DEL 48 Sq Ft Filters, R0501300","description":"\u003cp\u003eThe Jandy R0501300, also sold under the Zodiac name, is the complete grid assembly for the 48 sq ft DEV and DEL DE filters. It is the full grid set and the manifold in one pre-assembled unit, which makes it the quick way to bring a tired DE filter back to full filtration.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuilt for the tank\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe assembly is shaped to fit the DEV48 and DEL48, and the grids and frame are made from materials chosen to resist pool chemicals and UV over many seasons. The manifold distributes water evenly across the grids so the entire 48 sq ft of filter area is working.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBecause it arrives assembled, the job is to open the tank, lift out the old grid assembly and set the new one in place. There is no stacking individual grids or lining up a manifold on the bench.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck the size\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe 60 sq ft DEV60 and DEL60 filters use a different complete assembly, so confirm your filter is the 48 sq ft model before ordering.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624880419028,"sku":"R0501300","price":479.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_68f0e27f-3720-4ee2-b7ee-6a7562c57f32.jpg?v=1788648884"},{"product_id":"jandy-tank-top-cl340-cl460","title":"Jandy CV Series Cartridge Filter Tank Top R0554700","description":"\u003cp\u003eThe Jandy R0554700 is the upper half of the filter tank on the CV and CL series cartridge filters and the DEV and DEL series DE filters. It is the genuine Jandy part, packaged under the Jandy or Zodiac name.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt fits the CV340, CV460, CL340, CL460, DEV48 and DEL48. Check the model on your filter label against that list; the 580 cartridge and 60 sq ft DE sizes take a different top.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat comes with it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe tank top only. The tank body o-ring, the clamp ring assembly, the gauge and the internal manifold are separate parts. If the o-ring is flattened, cracked or has been in service for years, replace it while the tank is open so the new top seals properly on the first try.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624880648404,"sku":"TLD-051-5027","price":522.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_74525b92-e377-4fe7-b238-9fe54a3e38d5.jpg?v=1788648912"},{"product_id":"r0457502-igniter-kit-jxi-jandy-pro-series","title":"Jandy Igniter Kit for JXi Heater Models 200\/260\/400, R0457502","description":"\u003cp\u003eThe Jandy R0457502 is the genuine replacement igniter kit for JXi pool heaters in the 200, 260 and 400 sizes, including the JXi Jandy Pro Series. The igniter is the component that lights the burner on each call for heat, and it is one of the parts most often replaced on a gas heater as it ages.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA heater that runs its blower on a call for heat but never lights, then locks out on an ignition fault, often has a failed igniter. A visible crack in the element confirms it. Fitting the R0457502 kit restores normal ignition.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm your heater is a JXi 200, 260 or 400 before ordering. This kit is specific to that line.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624883728596,"sku":"LAR-151-3220","price":61.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_1614d399-2efa-49cd-b7ab-ceff4a7b0374.png?v=1788649543"},{"product_id":"manifold-assembly","title":"Jandy Genuine OEM Manifold Assembly for DEV48\/60 and DEL48\/60 DE Filters, R0359000","description":"\u003cp\u003eThe Jandy R0359000 is the manifold assembly for the DEV48 and DEV60 DE filters and their DEL48 and DEL60 counterparts. It is the genuine Jandy part, not an aftermarket copy, so it matches the original in shape and fit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eInside a Jandy DE filter the grids mount to the manifold, and the manifold sits in the tank as the backbone of the grid assembly. If the original has cracked, warped or lost a fitting, water can bypass the grids and send DE back to the pool. Swapping in a new manifold restores the assembly without replacing the grids themselves.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm your filter is a DEV48, DEV60, DEL48 or DEL60. While the tank is open, inspect the tank body o-ring and replace it if it is worn, since it is the one seal that keeps the tank halves tight.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624885006548,"sku":"TLD-051-5023","price":116.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4bbdfbac-f102-4fa7-b956-4a5477839ef7.jpg?v=1788649704"},{"product_id":"lid-locking-ring-assembly-w-o-ring","title":"Jandy Lid \u0026 Locking Ring Assembly with O-Ring, R0445800","description":"\u003cp\u003eThe Jandy R0445800 is the complete lid and locking ring assembly, with o-ring, for the Jandy Stealth SHPF and SHPM pumps and the ePump JEP variable speed pumps. The lid is stamped A0577900; R0445800 is the number you order it under.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat you get\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA clear plastic trap lid 10-1\/16 in. across, the 4 tab twist lock ring that holds it down and a fresh lid o-ring. Buying the three together means a cracked lid, a stripped ring or a flattened o-ring are all dealt with in one swap, and the clear lid lets you check the basket and water level without opening the pot.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm the pump is a Stealth SHPF or SHPM or an ePump JEP, and if you can, check that the old lid is stamped A0577900.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624885334228,"sku":"TLD-101-2031","price":117.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_04b93a9b-2765-459f-82d3-1880dc2a48f1.png?v=1788649767"},{"product_id":"backplate-kit-fhp","title":"Jandy FHP Flo Pro Backplate Kit, R0479500","description":"\u003cp\u003eThe Jandy R0479500 is the genuine backplate kit for the FloPro line of pumps. It fits the FHPM series from 0.75 through 2.5 HP, the FHPF series and the VS FloPro, and it comes with the three parts the job needs: the backplate, the o-ring that seals it to the housing, and a new shaft seal.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the kit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe backplate is the seal plate that sits between the motor and the wet end. When it cracks or warps, water leaks out behind the impeller and air gets drawn in, which shows up as a drip under the motor or bubbles in the basket that no suction side fix will cure. The shaft seal lives in the same plate and is the pump's main wear item, so Jandy packs a fresh one with the plate rather than have you reuse a seal that has already run.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe plate mounts in place of the original with the pump apart at the housing clamp. It covers the whole FHPM horsepower range and the VS FloPro, so one part number serves most FloPro installations.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624886382804,"sku":"TLD-101-2042","price":103.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_bfca08a6-56aa-4fb0-a4d7-554979a4af3b.jpg?v=1788649941"},{"product_id":"valve-actuator-jva-24v","title":"Jandy Valve Actuator JVA 24V, 4424","description":"\u003cp\u003eThe Jandy 4424 is the 24V valve actuator for Jandy Pro Series NeverLube and gray 2 and 3 port diverter valves. Mounted on the valve, it turns the diverter under command from an AquaLink RS system, switching between pool and spa or driving water features without anyone touching a handle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat changed\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the newer design, with easier cam adjustment, a PCB and a hidden toggle switch. It rotates 180 degrees and can be set to stop the diverter at any position, not only at the ends of travel.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eLabels\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eUnits have shipped labeled JVA2440 and, after Jandy made internal improvements, JVA2444. Both are part number 4424 and the same product.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624918036692,"sku":"JDY-30-6324","price":233.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_727a9994-6470-4a2e-8a7d-8194d6311719.jpg?v=1788653303"},{"product_id":"cell-kit-pools-up-to-12-000gal-16ft-cables","title":"Jandy AquaPure PureLink Salt Chlorine Generator Cell Kit, 12K Gallon Pools, PLC700","description":"\u003cp\u003eThe Jandy PLC700 is the AquaPure PureLink cell kit for pools up to 12,000 gallons. It is the replacement cell for Jandy salt systems running an AquaPure Power Pack or a PureLink Power Center, supplied with 16 ft cables.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBuilt to last on salt\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe cell is designed to control calcium buildup on its plates. Scale is what slowly kills a salt cell, so limiting it keeps chlorine production steady and stretches the time between replacements.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFits the pad you have\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt is a three port cell with 90 degree plumbing flexibility, which gives you options when the return line does not run straight through the spot where the cell has to sit. The 16 ft cables reach the power center without splicing in most installs.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCheck two things: that your pool is 12,000 gallons or under, and that your power center is an AquaPure Power Pack or a PureLink Power Center. Larger pools need a higher capacity cell from the same family.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624921084116,"sku":"JDY-45-0705","price":999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_8842a3a5-1407-4637-aa5a-e3bb19cfa04d.jpg?v=1788653530"},{"product_id":"tank-body-o-ring","title":"Jandy Tank Body O-Ring, R0357800","description":"\u003cp\u003eThe Jandy R0357800 is the tank body o-ring for a wide run of Jandy filters. It is a cord style ring that seals the joint between the two halves of the filter tank.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFits four families\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe DEV series DE filters (DEV48, DEV60), the DEL series DE filters (DEL48, DEL60), the CV series cartridge filters (CV340, CV460, CV580) and the CL series cartridge filters (CL340, CL460, CL580) all use this same o-ring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA tank that weeps at the clamp once the pump starts is the classic symptom. Any time the filter is opened for cleaning, look the ring over. If it is flattened, nicked or has stretched out of round, fit a new one before closing the tank.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eCheck your filter model against the list above. This is the genuine Jandy part.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624921247956,"sku":"TLD-101-6001","price":61.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_09b2a36d-11db-4749-99b8-6eea709101b7.jpg?v=1788653552"},{"product_id":"tank-clamp-ring-w-rod-assembly","title":"Jandy Tank Clamp Ring with Rod Assembly, R0357400","description":"\u003cp\u003eThe Jandy R0357400 is the tank clamp ring with rod and knob assembly for the CV and CL series cartridge filters and the DEV and DEL series DE filters. It is the genuine Zodiac Jandy part, supplied as a complete assembly with the rod and knob already fitted.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe clamp ring wraps the seam between the top and bottom halves of the filter tank and holds them together under pressure. The knob on the rod tightens and releases the ring by hand, which is how you get into the tank to clean cartridges or grids. When the ring cracks, the rod strips or the knob breaks, the tank cannot be closed with confidence, and the whole assembly should be replaced.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt fits the CV340, CV460 and CV580, the CL340, CL460 and CL580, and the DEV48, DEV60, DEL48 and DEL60. The ring measures about 23.5 in. across and 2.25 in. deep.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624922329300,"sku":"TLD-051-5039","price":329.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_daf854fc-f29b-49f4-b94c-b246ee5b7765.jpg?v=1788653619"},{"product_id":"2-x-2-1-2-pump-union-assembly","title":"Jandy 2\" x 2-1\/2\" Pump Union Assembly (Set of 2), R0449000","description":"\u003cp\u003eThe Jandy R0449000 is a set of two 2 in. by 2-1\/2 in. pump unions. Each union is the full three piece assembly: a tail piece, its o-ring and the coupling nut, so the pair covers both the suction and discharge sides of a pump. It is the genuine Zodiac Jandy part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe same union is used across three Jandy pump lines, the PlusHP in both PHPF and PHPM versions, the MaxHP MHPM and the WaterFeature WFTR. It is also the union on the Legacy LRZE and LRZM gas heaters from 2009 onward, so one part number covers the pump and the heater on many Jandy pads.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eUnions are what let you pull a pump or heater without cutting pipe. A cracked coupling nut, a warped tail piece or a flattened o-ring turns into a drip at the equipment, and a new union set is the clean fix. Replacing both sides at once keeps the two connections at the same age.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624922362068,"sku":"TLD-101-2028","price":48.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_d4db5336-f0a0-411f-846d-daf7ddbfeb77.png?v=1788653624"},{"product_id":"5hp-3hp-diffuser-w-o-ring-and-hardware","title":"Jandy 0.5 HP to 3 HP Diffuser with O-Ring and Hardware, R0445400","description":"\u003cp\u003eThe Jandy R0445400 is the genuine diffuser for Jandy's 0.5 through 3 HP pumps, supplied as a kit with the o-rings and hardware needed to fit it. One part number covers the Stealth SHPF and SHPM, PlusHP PHPF and PHPM, MaxHP MHPM, WaterFeature WFTR and the ePump JEP variable speed pumps.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIn the box\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOne diffuser, two screws, two washers and two o-rings. That is everything the diffuser needs to go back onto the pump with fresh seals, so there is no second order for the small parts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe diffuser sits over the impeller and shapes the flow into the volute. A cracked or worn diffuser costs the pump flow and can make it noisy or slow to prime. If the pump is already open for an impeller or shaft seal, it is the right time to fit a new diffuser as well.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm the pump is one of the listed Jandy families and rated between 0.5 and 3 HP. The horsepower range is broad on this part, so the family match is what matters.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624928653524,"sku":"TLD-101-2006","price":78.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_8fb341b2-a62b-442f-8111-655a86a7d202.jpg?v=1788654897"},{"product_id":"lid-with-lock-ring","title":"Jandy Lid with Lock Ring, R0480000","description":"\u003cp\u003eThe Jandy R0480000 is the strainer lid and locking ring for the FloPro family of pumps. It is the clear plastic lid you look through to check the basket, together with the four tab ring that clamps it to the pump body and the lid o-ring that seals it. All three come in the kit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitment\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt fits the FloPro FHPM and FHPF pumps from 0.75 through 2.5 HP and the VS FloPro. The lid measures 6-7\/8 in. across. If your pump is one of these models and the old lid matches that size, this is the part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eLids fail two ways: the plastic clouds and cracks with sun and age, or the lock ring tabs wear until the lid will not clamp tight. Either one lets air into the strainer, and a pump that draws air loses prime and runs hot. A worn o-ring shows the same symptom and is worth trying first if the lid itself looks sound; the R0480200 ring is included here and also available separately.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624929767636,"sku":"TLD-101-2041","price":88.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_8ed40895-e6fb-4df6-9c9d-47688cdd4bce.png?v=1788654962"},{"product_id":"mechanical-seal-5-8-id","title":"Jandy Mechanical Seal, 5\/8\" ID, R0479400","description":"\u003cp\u003eThe Jandy R0479400 is the Pro Series mechanical shaft seal, a carbon and ceramic pair with a 5\/8 in. inside diameter on the ceramic. It is the genuine Jandy part for Stealth SHPF and SHPM pumps from serial number P08FF0001 onward, for the Zodiac Jandy ePump JEP variable speed pumps, and for the Flo Pro FHPM and VS-FHP variable speed models.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e5\/8 in. or 13\/16 in.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eStealth pumps changed shafts partway through production. Revision N and earlier impellers sat on a double stepped shaft and need a seal with a 13\/16 in. inside diameter on the ceramic. Revision P and later have no step where the impeller mounts, and those pumps take this 5\/8 in. seal. Check the revision or measure the shaft before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe shaft seal is what keeps pool water out of the motor. Replace it every time the impeller comes off, and any time water weeps from the joint between the pump body and the motor. It is a small part that saves a motor.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624930160852,"sku":"TLD-101-2032","price":34.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_7575685b-4ac7-4244-a991-50330f1c4588.png?v=1788655038"},{"product_id":"manifold-assembly-cl-cv-series-new-style","title":"Jandy Manifold Assembly CL \/ CV Series Cartridge Filters, R0357600","description":"\u003cp\u003eThe Jandy R0357600 is the manifold assembly for the Zodiac Jandy CL and CV series cartridge filters. It is the genuine Jandy part and fits all six models in the two lines: CL340, CL460 and CL580, and CV340, CV460 and CV580, on both pool and spa installations.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNew style\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eJandy has redesigned this manifold. The current version is slimmer than the bulky original, so it may not look like the part coming out of your tank. That is expected. The new style is the only version supplied now, and it fits every CL and CV filter, including tanks that were built with the old design.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm your filter is a CL or CV model from the list above. A cracked manifold lets unfiltered water bypass the cartridges, so it is worth replacing as soon as it is found rather than running the season on it.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624930193620,"sku":"TLD-051-5030","price":146.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_02a94c0d-753b-495f-8204-284f05dd6412.jpg?v=1788655042"},{"product_id":"back-plate-kit","title":"Jandy Back Plate Kit, R0445200","description":"\u003cp\u003eThe Jandy R0445200 back plate kit is the genuine Jandy rebuild kit for the seal end of the Stealth, PlusHP, MaxHP, WaterFeature and ePump pumps. It puts a new back plate, a new mechanical seal and new hardware in one box.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIn the box\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOne back plate, one carbon seal half and one ceramic seal half making up the R0479400 mechanical seal, one o-ring, and eight bolts with washers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy replace the plate with the seal\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe ceramic half of the shaft seal seats in the back plate. If the plate is scored, pitted or cracked, a new seal will not hold for long. Replacing both at once, with fresh bolts instead of corroded originals, is the reliable way to stop a pump that leaks between the body and the motor.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eJandy Stealth SHPF and SHPM, PlusHP PHPM and PHPF, MaxHP MHPM, WaterFeature WFTR and the ePump JEP1.5 and JEP2.0 variable speed pumps.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624930390228,"sku":"TLD-101-2030","price":183.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_810d0e86-72b6-4327-9378-066619458226.png?v=1788655062"},{"product_id":"check-valve-kit-for-1-5-2-5-check-valve-body","title":"Jandy Check Valve Kit for 1.5 in. to 2.5 in. Check Valve Body, 7056","description":"\u003cp\u003eThe Jandy 7056 is the replacement flapper assembly kit for Jandy's heavy duty black check valves. It fits the 7235, 7305, 7511 and 7512 valve bodies, which cover 1.5 in. to 2.5 in. plumbing and share the lid held down by eight screws. The kit contains the flapper assembly, the pin and the spring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy rebuild\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA check valve fails at the flapper long before the body wears out. The seal face gets nicked, the spring loses tension, or the pin wears and the flapper hangs. Any of those lets water drain back through the valve when the pump stops, which is how a spa loses its level or a pump loses prime overnight. Swapping the internals fixes that without cutting the valve out of the line.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eShut the pump off, relieve pressure, remove the eight lid screws and lift the lid. Pull the old flapper, pin and spring, drop the new assembly in, seat the spring, and refit the lid. Inspect the lid o-ring while you are in there; it is a separate part and worth replacing if it has flattened.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624930586836,"sku":"JDY-561-2322","price":71.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_e59adc7a-f4a2-4030-9b7d-64b7d79990d5.jpg?v=1788655102"},{"product_id":"jandy-r0745700-2-top-mount-multi-port-valve","title":"Jandy 2 in. Top Mount Multi-Port Valve, R0745700","description":"\u003cp\u003eThe Jandy R0745700 is the complete top mount multiport valve, 2 in. ports, with clamp assembly, for the Jandy Pro Series SFTM24-2.0 sand filter. It is the Brand OEM Jandy part, sold under the Zodiac and Jandy names.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA top mount valve sits on the tank neck and clamps down over the tank flange. It restores filter, backwash and rinse control in one lever. It replaces the valve on the filter when the body cracks, the lever no longer indexes cleanly or water leaks between positions.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe multiport valve and the clamp assembly that secures it to the tank flange. Both arrive together so the swap can be done in one go.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSized for the SFTM24-2.0, the 24 in. top mount filter plumbed in 2 in. The ports are 2 in., to match that plumbing. Check the model plate on your tank before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe listing covers the valve and clamp assembly. Check the valve to tank o-ring during the swap and replace it if it is worn.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624934715604,"sku":"TLD-06-1001","price":346.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_a01e2f4c-1f21-4e43-a289-f2e87d18adcb.png?v=1788655208"},{"product_id":"jandy-r0745100-filter-clamp-assembly-and-hardware","title":"Jandy Filter Clamp Assembly and Hardware, R0745100","description":"\u003cp\u003eThe Jandy R0745100 is the flange clamp assembly for the Pro Series SFTM top mount sand filters. It is the band that holds the multiport valve down on the tank, and it comes with the hardware needed to fit it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt fits the two SFTM models, the 22 in. SFTM22-1.5 and the 24 in. SFTM24-2.0. This is the genuine Zodiac Jandy part.\u003c\/p\u003e\u003cp\u003eA clamp that has cracked, corroded or lost its hardware lets the valve shift on the tank. If yours has been leaking at the flange, inspect the tank o-ring under the valve when you have the clamp off and replace it if it is flattened or nicked.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624937304276,"sku":"TLD-051-1006","price":71.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_01447d24-2c88-497c-ae03-c8577330d180.png?v=1788655632"},{"product_id":"2-union-universal-tailpiece","title":"Jandy 2\" Union\/Universal Tailpiece, R0452100","description":"\u003cp\u003eJandy R0452100 is the union kit for AquaPure 3-port salt cells. It supplies everything at the two plumbing connections: universal union nuts, o-rings, 2 in. tailpieces and a plug. The same kit is called out in the Zodiac Nature2 Fusion Soft and Nature2 Fusion Inground parts breakdowns.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen you need it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOrder it when a union nut has cracked, a tailpiece has been damaged during a cell change, or you are installing a cell into new plumbing and want matched, genuine fittings. Because the o-rings are included, a cell that has started weeping at the unions can be resealed at the same time.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis kit is for 2 in. plumbing and the three port AquaPure cell. Check the cell body for the port count before ordering.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624941105364,"sku":"JDY-451-0204","price":27.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_a77e8c50-f256-4fec-90f2-42e671cced5f.jpg?v=1788655935"},{"product_id":"jandy-truclear-11k-cable-cell-side","title":"Jandy TruClear Cable Assembly and Cell Side Wire Connector, R0840300","description":"\u003cp\u003eThe Jandy R0840300 is the TruClear cable assembly with the cell side wire connector, for the Jandy TruClear salt chlorinator (model TRUCLEAR11K). It is a Jandy part for the electrical connection on the cell side of the system.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow the TruClear connects\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eJandy describes the TruClear cell as removable, with an attached cord and a tool-free twist-lock connector for the electrical connection to the power pack. Jandy's manual says the cell must be installed horizontally with the cord facing upwards, so that flammable gases cannot build up around it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm that you have a TruClear before ordering. Jandy lists the TruClear cell (R0693900), cell housing (R0694000), O-ring (R0694100) and power pack (R0802200) as separate parts, so this cable assembly is not any of those. A TruClear treats pools up to 35,000 gallons, produces 18.4 g of chlorine an hour and runs on 120 or 240 VAC.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624956604628,"sku":"R0840300","price":111.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_425e43e4-6f1b-4bbb-a410-350cadeff3f3.jpg?v=1788656017"},{"product_id":"jandy-r0589600-access-door-kit-for-jxi-heaters","title":"Jandy Access Door Kit for JXi Heaters, R0589600","description":"\u003cp\u003eThe Jandy R0589600 is the access door kit for Jandy JXi gas-fired pool and spa heaters in the 200, 260 and 400 sizes, supplied with the door, an O-ring seal and screws. It is item 28 in Jandy's JXi parts list, and one kit number covers all three heater sizes.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is in the kit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eJandy's parts table describes R0589600 as an access door kit made up of a door, an O-ring seal and screws. Because the seal is part of the kit, the door goes back on with a fresh O-ring instead of the worn one that came off.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe part is listed for the JXi 200, 260 and 400. This listing is for the JXi series only, so check the parts list in your heater manual against the model number on the heater before you order.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRelated JXi service parts\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe same Jandy parts table lists the R0589700 thermal regulator valve, the R0589800 bypass kit, the R0446000 drain plug and the R0589500 gasket and seals kit for the heater manifold. Jandy publishes spare parts installation instructions for the JXi (document H0439300). They begin with switching off electrical power and the main gas supply and draining the heater, and the work should be done by a qualified pool equipment professional.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624956899540,"sku":"LAR-151-3255","price":43.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_d4aaf2eb-1c83-42a5-86c1-96c4ca3de576.jpg?v=1788656060"},{"product_id":"zodiac-r0465400-tank-bottom-assembly-for-cv340-460-580-filters","title":"Jandy Tank Bottom Assembly for CV340\/460\/580 Filters, R0465400","description":"\u003cp\u003eThe Jandy R0465400 is the lower tank assembly for the CV Series cartridge filters, covering the CV340, CV460 and CV580. It is the genuine Jandy part and the same item sold under the Zodiac name.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen you need it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA filter base that has cracked, or that weeps at the drain or around the bulkhead, is normally the end of the road for the tank but not for the filter. Swapping the bottom half keeps the existing top, cartridge and plumbing in service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm your filter is a CV340, CV460 or CV580. The assembly ships in black or gray depending on what Jandy is producing, so it may not match the shade of your current tank. Since the filter will be fully apart for the swap, it is a good time to inspect the tank body o-ring and replace it if it is flattened or cracked.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624957259988,"sku":"TLD-051-5077","price":678.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_69b5f216-019a-4a94-9d65-ec8bf5a625c2.jpg?v=1788656080"},{"product_id":"zodiac-r0589700-thermal-regulator-valve-for-model-200-260-400-jxitm-heaters","title":"Jandy Thermal Regulator Valve for Model 200, 260, 400 JXi Heaters, R0589700","description":"\u003cp\u003eThe Jandy R0589700 is the thermal regulator valve for the JXi pool and spa heaters in the 200, 260 and 400 sizes. It is the genuine Jandy part, also listed under the Zodiac name with the same number.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe thermal regulator lives in the heater header and governs how much water flows through the heat exchanger. By holding flow back until the exchanger is warm it lets the heater reach its working temperature quickly and keeps it there, which is what protects the exchanger over the long run.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm your heater is a JXi 200, 260 or 400 and that R0589700 is the regulator called out in its parts list.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624957325524,"sku":"LAR-151-3233","price":102.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/LAR-151-3233_1a.png?v=1788656089"},{"product_id":"zodiac-r0694100-o-ring-for-jandy-pro-series-truclear-chlorine-generating-system","title":"Jandy O-Ring for TruClear Cell, R0694100","description":"\u003cp\u003eThe Jandy R0694100 is the genuine o-ring for the cell on the Jandy Pro Series TruClear chlorine generating system. It is a Zodiac part, listed under both the Jandy and Zodiac names.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eReplace the o-ring whenever the TruClear cell is removed for acid cleaning or swapped for a new one, and right away if the cell connection begins to weep. An o-ring that has been compressed for a season takes a set and seldom seals reliably once it has been disturbed, and a slow drip at the cell is the kind of leak that goes unnoticed until the pad is wet.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstalling it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eClean the groove, coat the new o-ring lightly with a silicone based lubricant, and seat it evenly before tightening the cell. Keep a spare on hand so the next cleaning does not wait on a part.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624958079188,"sku":"JDY-45-9882","price":18.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_066888b8-2138-47cc-8785-a97b61e7037f.jpg?v=1788656180"},{"product_id":"breather-tube-assembly","title":"Jandy Breather Tube Assembly Replacement Kit, R0358700","description":"\u003cp\u003eThe Jandy R0358700 is the genuine breather tube assembly kit for Jandy cartridge and DE filters. The breather tube gives air trapped at the top of the tank a way out, so the filter runs full of water and filters the way it should. When the tube cracks or breaks, air collects in the tank and performance falls off.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOne part covers ten filters: the CV340, CV460 and CV580 and the CL340, CL460 and CL580 cartridge filters, and the DEV48, DEV60, DEL48 and DEL60 DE filters.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAbout the design change\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eJandy has revised this assembly, so the part you receive may not look identical to the one you remove. It fits the same filters. Match your filter model to the list rather than the appearance of the old tube.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624959553748,"sku":"TLD-051-5021","price":26.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c5441756-264f-43f9-9645-0428448eb55c.jpg?v=1788656545"},{"product_id":"seal-lid","title":"Jandy Lid Seal, R0446200","description":"\u003cp\u003eThe Jandy R0446200 is the genuine lid seal for the Stealth SHPF and SHPM series pumps and the ePump JEP2.0 and JEP1.5 variable speed pumps. It seals the clear strainer lid to the pump body, and it is the first thing to check when a Jandy pump starts pulling air.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eTwo o-rings, one kit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe kit contains two o-rings of the same size, 8-1\/2 in. outside diameter and 8 in. inside diameter. One has a standard round cross section, the other a square cross section. Match the profile of the seal you removed and keep the other as a spare.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBubbles in the strainer pot, slow priming or a pump that loses prime after it shuts off all point to air getting in at the lid. If the seal is flattened, cracked or stiff it will not hold. Clean the groove, fit the new seal with a light coat of silicone lubricant and hand tighten the lid.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624959619284,"sku":"TLD-101-2019","price":32.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_eea52da1-e0fb-4c46-9c4c-ff0a1fdd0754.png?v=1788656554"},{"product_id":"jxi-user-interface-kit","title":"Jandy JXi User Interface Kit for Model 200\/260\/400, R0591900","description":"\u003cp\u003eThe Jandy R0591900 is the genuine user interface kit for the JXi pool heaters in the 200, 260 and 400 sizes. It is the control face on the front of the heater, where the temperature is set, pool or spa mode is chosen and status and fault codes are read.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen you need it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA display that stays dark while the heater has power, buttons that no longer respond, or an interface that has taken on water and behaves erratically all point to the user interface. Replacing the kit is a fraction of the cost of a new heater.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIsolate power to the heater before opening the control compartment, transfer the harness connections to the new interface and refit the cover. Check the model size on your data plate is 200, 260 or 400 before ordering.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624959979732,"sku":"LAR-151-3247","price":246.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_81403d58-614d-4191-bf04-0de6a2b25aa3.jpg?v=1788656611"},{"product_id":"pump-body-phpf-phpm","title":"Jandy Pump Body PHPF\/PHPM, R0448700","description":"\u003cp\u003eThe Jandy R0448700 is the pump body housing for the PlusHP PHPF and PHPM series pool pumps. It is the genuine Jandy replacement for the wet end casing that the impeller and diffuser run inside.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen it is the right repair\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA pump body cracks from a hard freeze or an impact, or its threads and sealing surfaces wear to the point that the pump loses prime or leaks at the housing. Replacing the body puts the original motor and hardware back to work without the cost of a complete pump.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm your pump is a PHPF or PHPM series PlusHP. The lid and lock ring assembly with seal and the filter basket for these pumps are separate parts if you are rebuilding the whole wet end.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624967057620,"sku":"TLD-101-2009","price":356.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_05627b25-3dcc-46bc-94e5-2432b68a7fc0.jpg?v=1788656839"},{"product_id":"pump-basket","title":"Jandy Pump Basket for FHPM\/FHP Series Pumps, R0480100","description":"\u003cp\u003eThe Jandy R0480100 is the debris trap basket for Jandy FloPro pumps in the FHPM and FHP series, including the VS FloPro variable speed models. It sits in the strainer pot ahead of the impeller and catches leaves, twigs and anything else that makes it past the skimmer.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe basket is 9-9\/16 in. tall. The top rim measures 5-7\/16 in. outside and 4-9\/16 in. inside, and the bottom is 4-7\/16 in. across. Compare against your old basket before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eReplacement\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eShut the pump off, open the lid, lift the old basket out and set the new one in place. Make sure it seats fully so the lid closes without pressing on the rim, which is the usual cause of a cracked basket.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624968630484,"sku":"TLD-101-2033","price":30.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b3065028-77dd-4d11-8017-929c02b53bfb.jpg?v=1788656882"},{"product_id":"zodiac-r0621900-winterizing-cap-for-jandyr-pro-series-trucleartm-chlorine-generating-system","title":"Jandy Winterizing Cap for Pro Series TruClear Chlorine Generating System, R0621900","description":"\u003cp\u003eThe Jandy R0621900 is the winterizing cap for the Pro Series TruClear chlorine generating system. At closing time it seals the salt cell off from the rest of the plumbing, so water cannot sit in or flow into the cell while the pool is shut down for the winter.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSimple to use\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe cap goes on by hand at closing and comes off at opening, with no tools. It is small and light, so it stores easily during the swim season, and its corrosion resistant construction means it lasts through many winters of salt water exposure.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePart of a complete winterization\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIf you are closing a TruClear system, it is a good time to inspect the cell o-ring and housing as well. Both are available as separate Jandy parts.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48624971677908,"sku":"JDY-45-9881","price":71.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6916e0cc-1b5c-4c2b-8c9d-bbef00246619.jpg?v=1788657045"}],"url":"https:\/\/www.activepoolsupply.com\/collections\/jandy-parts.oembed?page=3","provider":"Active Pool Supply","version":"1.0","type":"link"}