{"title":"Valve Parts","description":"\u003cp\u003eShop valve parts at Active Pool Supply, with genuine OEM and quality aftermarket options.\u003c\/p\u003e","products":[{"product_id":"cover-o-ring-sp0714t","title":"Hayward Cover O-Ring for SP0714T Vari-Flo XL Valve","description":"\u003cp\u003eThe Hayward SPX0714L is the top cover o-ring for the SP0714T Vari-Flo XL multiport valve, the 1.5 in. top mount valve on Hayward sand filters. It measures 6 in. outside diameter, 5 5\/8 in. inside diameter and 3\/16 in. thick.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it fixes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWhen water weeps from the seam between the valve cover and the body, under the handle, this o-ring has usually flattened, cracked or been pinched. It is a small part, and it is worth replacing any time the cover is off for a diverter gasket, spring or handle repair.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstalling it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eClean the groove, apply a thin film of silicone based o-ring lubricant, seat the ring and tighten the cover screws evenly. If the leak is between the valve and the filter tank rather than at the cover, the larger tank o-ring is the part you need.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48624872620244,"sku":"HAY-061-2140","price":17.62,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_f02fdf2f-119b-4ad0-8f40-da382eca0f02.jpg?v=1788647826"},{"product_id":"6-port-water-valve-module","title":"Paramount 6 Port Water Valve Module","description":"\u003cp\u003eThe Paramount 6 port water valve module, part 004-302-4408-00, is the replacement module for the Paramount 6 port valve used on in-floor pool cleaning systems. It is also sold under the name Hydro 6 module. The valve indexes water between six outlet ports so each set of cleaning heads gets its turn, and the module is the part that does that work.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSystems it fits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003ePCC 2000, Pool Valet, PV3, Cyclean, Vanquish, Paddock PCC 2000, Andrews Advantage PCC2000 and Vantage in-floor cleaning systems that use the Paramount 6 port valve.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eModule, not the whole valve\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eYou replace the internals and leave the valve body plumbed in place. If some zones never come on, or the valve sticks on one zone while the pump runs, the module is the usual cause. A complete 6 port 2 in. valve is available separately if the body itself is cracked.\u003c\/p\u003e","brand":"Paramount","offers":[{"title":"Default Title","offer_id":48624878911700,"sku":"PMT-201-604","price":327.38,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_09f65595-cdb1-4cc3-bb80-eb20ddf2eada.jpg?v=1788648631"},{"product_id":"key-cover-handle-assembly","title":"Hayward OEM Key Cover and Handle Assembly for SP740DE","description":"\u003cp\u003eThe Hayward SPX0740BA is the key cover and handle assembly for the SP740DE, Hayward's 2 in. multiport valve for DE filters. It is the genuine Hayward part and ships with the valve seat gasket and the o-ring, so the valve can be sealed up again in the same job.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it replaces\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA cracked cover, a handle that has gone loose or brittle, or a top end that weeps at the cover are all fixed by swapping this assembly. The cover, key and handle come as one unit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm the valve is the 2 in. SP740DE. The key stem underneath is a separate part, so if the valve has been hard to turn or will not hold position, inspect the stem while the cover is off.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48624918495444,"sku":"HAY-061-2651","price":166.04,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_d46afaa0-5ea3-4a22-b0e9-bac13c012971.jpg?v=1788653392"},{"product_id":"check-valve-kit-for-1-5-2-5-check-valve-body","title":"Jandy Check Valve Kit for 1.5 in. to 2.5 in. Check Valve Body","description":"\u003cp\u003eThe Jandy 7056 is the replacement flapper assembly kit for Jandy's heavy duty black check valves. It fits the 7235, 7305, 7511 and 7512 valve bodies, which cover 1.5 in. to 2.5 in. plumbing and share the lid held down by eight screws. The kit contains the flapper assembly, the pin and the spring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy rebuild\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA check valve fails at the flapper long before the body wears out. The seal face gets nicked, the spring loses tension, or the pin wears and the flapper hangs. Any of those lets water drain back through the valve when the pump stops, which is how a spa loses its level or a pump loses prime overnight. Swapping the internals fixes that without cutting the valve out of the line.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eShut the pump off, relieve pressure, remove the eight lid screws and lift the lid. Pull the old flapper, pin and spring, drop the new assembly in, seat the spring, and refit the lid. Inspect the lid o-ring while you are in there; it is a separate part and worth replacing if it has flattened.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48624930586836,"sku":"JDY-561-2322","price":65.22,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_e59adc7a-f4a2-4030-9b7d-64b7d79990d5.jpg?v=1788655102"},{"product_id":"low-profile-t-valve-kit","title":"Pentair 2 in. 6 Port Low Profile T-Valve Kit","description":"\u003cp\u003eThe Pentair 230069 is the genuine T-valve kit for the Pentair 6 port low profile water valve. It is sized for 2 in. pipe.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm that your valve is the low profile version of the 6 port water valve and that your plumbing is 2 in. The kit is a direct replacement on that combination.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48624996843732,"sku":"ANA-20-0011","price":139.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_066781e5-d52b-446c-b64b-47e5f65abf88.png?v=1788661627"},{"product_id":"pentair-handle-fullflo-xf-bw-valve-270187z","title":"Pentair Replacement Handle for FullFloXF Backwash Valve","description":"\u003cp\u003eThe Pentair 270187Z is the genuine replacement handle for the FullFloXF backwash valve. It replaces a handle that has cracked, snapped or gone missing, so the valve can be shifted between positions again without replacing the valve itself.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the handle only. It is the right repair when the valve body still seals and shifts correctly and the handle is the only damaged part.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48624996942036,"sku":"AMP-061-2000","price":53.38,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c97e6736-4533-4ffc-b949-7f98caab8acd.jpg?v=1788661635"},{"product_id":"hayward-psxcvba-psv-check-valve-cover-and-flapper-replacement-kit","title":"Hayward PSV Check Valve Cover and Flapper Replacement Kit","description":"\u003cp\u003eThe Hayward PSXCVBAH is the replacement cover and flapper kit for the Hayward PSV check valve. It is the genuine Hayward part, also listed as PSXCVBA.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe flapper is the moving part of a check valve, and the cover is what holds it in the body. Replacing both puts the valve back to holding one way flow without cutting the valve body out of the plumbing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to order it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWhen water runs backward through the valve after the pump stops, or the flapper no longer seats cleanly.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48624998711508,"sku":"HAY-561-1014","price":38.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_31cc9909-2e0d-4118-809f-543a624f3f94.jpg?v=1788661801"},{"product_id":"2-valve-seat-gasket-6-1-2","title":"Hayward 2\" Valve Seat Gasket (6-1\/2\")","description":"\u003cp\u003eThe Hayward SPX0715D is the genuine valve seat spider gasket for 2 in. Vari-Flo side mount multiport valves, the SP-715 and SP-716 models. It is the same part Hayward also lists as SPX715D.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe gasket measures 6-1\/2 in., with a 6-5\/16 in. outside diameter and a 3\/4 in. center hole. Measure your old gasket against those numbers; the 1.5 in. Vari-Flo valves take a smaller one.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy you replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe spider gasket seals the diverter against the valve body between ports. When it wears or a spoke pulls loose, water bypasses to the waste line while the filter is running, or backwash water finds its way back to the pool. A new gasket, seated dry and clean, cures it.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48625022959828,"sku":"HAY-061-3197","price":39.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_0f956f20-6681-448f-8cb4-5f432a3b3540.jpg?v=1788662559"},{"product_id":"2-valve-rebuild-kit","title":"SuperPro 2 in. Valve Rebuild Kit","description":"\u003cp\u003eThe SuperPro GO-KIT70 is a rebuild kit for Pentair, formerly Pac-Fab, 2 in. multiport valves, models 261055 and SM-20. It is a generic kit built to fit the valve rather than an OEM assembly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is in the kit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eOne G-160 sight glass gasket, one G-417 diverter spider gasket, two O-83 valve adapter o-rings, one O-160 valve adapter o-ring, two O-276 shaft seal o-rings, one O-284 body o-ring and one O-479 valve top o-ring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy valves get rebuilt\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe spider gasket is the usual culprit. When it hardens or tears, water bypasses the diverter and runs out the waste line even with the handle set to filter, which reads at the pool as a level that keeps dropping. Shaft seal o-rings weeping at the stem and a drip at the sight glass are the other two common complaints, and this kit covers all of them in one teardown.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoing the job\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSince the valve has to come apart anyway, replace every seal in the kit rather than only the one that failed. The rest are the same age.\u003c\/p\u003e","brand":"Aladdin","offers":[{"title":"Default Title","offer_id":48625724031188,"sku":"ALA-601-6088","price":19.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_eaaad72e-da0c-40b8-81e4-b4f445dca788.jpg?v=1788690092"},{"product_id":"diverter-w-gasket","title":"Pentair 1.5 in. HiFlow Diverter with Gasket","description":"\u003cp\u003eThe Pentair 272512Z is the HiFlow diverter with gasket for PacFab 262506 and 261130 top mount valves. It is the genuine Pentair part, also listed as 272512.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe gasket is part of the piece\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe 4 spoke gasket is molded into the bottom of the rotor. It cannot be bought on its own and it cannot be peeled off and replaced, so when the sealing face is worn the diverter goes in as a unit. That is worth knowing before you go looking for a separate spider gasket for this valve.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMeasurements\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eRotor 5-11\/16 in. with a total height of 4-3\/4 in. and a shaft diameter of 1-1\/8 in. The gasket measures 5-5\/16 in. outside diameter with a 1-7\/16 in. center hole. Spoke thickness and outside ring thickness are both 1\/8 in. side to side.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA worn diverter face lets water bypass inside the valve, so the pool level drops while the handle is set to filter, or the returns run weak on a backwash. Compare the measurements above against the old rotor to confirm you have the right valve before ordering.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48625724063956,"sku":"PAC-061-8968","price":55.73,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_2c98c2dd-6785-4cae-ad97-aebb7b1a6471.png?v=1788690096"},{"product_id":"oem-2-diverter-gasket","title":"Pentair 2 in. Multiport Valve Diverter Gasket","description":"\u003cp\u003eThe Pentair 271148Z is the diverter gasket for 2 in. multiport backwash valves. Most people know it as the spider gasket, after the star shape of the seal. It is the genuine PacFab part, also listed as 271148.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eInside a multiport, the diverter presses down onto this gasket. The arms of the star separate the ports from each other, so when the handle says filter, water goes to the filter and nowhere else. As the rubber flattens, hardens or tears, water crosses between ports. The usual symptom is a steady stream out of the waste line while the valve is set to filter, and a pool that slowly drops.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSize and fit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e6.75 in. in diameter and 0.64 in. thick. It is used on Pentair PacFab 2 in. top mount and side mount multiport valves, American Products 2 in. H and M series multiports, and the 6 position top mount clamp on valves 501130, 501131 and 501231. Compare the old gasket to the dimensions above before fitting the new one.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48625724555476,"sku":"PAC-061-9576","price":38.32,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_f72b67de-a94e-4434-9970-d68cb894f90f.png?v=1788690142"},{"product_id":"sp715-multiport-valve-repair-kit-2-with-spring","title":"Aladdin SP715 Multiport Valve Repair Kit 2\" with Spring","description":"\u003cp\u003eThis is the repair kit for the Hayward Vari-Flo 2 inch side mount multiport valves, models SP-715 and SP-716. It is an Aladdin aftermarket kit, part number APCKIT39, and this version includes the spring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat to know before fitting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe non metallic bearing supplied in the kit, the nylon washer, is smaller than the one currently sitting in the valve. It will not take its place. If the washer in your valve is worn, order Hayward SPX0710Z16 separately and use that instead. Everything else in the kit is intended to go straight in.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy rebuild the valve\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA side mount multiport that leaks between ports, will not hold a setting or pushes water to waste in filter position is usually worn internally rather than broken. A kit puts the wear parts back to new for a fraction of the cost of a new valve head.\u003c\/p\u003e","brand":"Aladdin","offers":[{"title":"Default Title","offer_id":48625743167700,"sku":"GO-KIT39-SPNG","price":46.94,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_8336f1aa-9cab-4338-b498-f87675569372.jpg?v=1788690565"},{"product_id":"pentair-270190z-fullfloxf-backwash-valve-end-cap","title":"Pentair FullFloXF Backwash Valve End Cap","description":"\u003cp\u003ePentair 270190Z is the replacement end cap for FullFloXF backwash valves. It is the genuine factory cap for the valve body.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the cap does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe end cap closes the top of the backwash valve and guides the stem that moves between filter and backwash. It takes the load every time the valve is pulled and pushed, which is why it is the part that eventually cracks rather than the valve body.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCap or O-rings\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWater appearing at the top of the valve has two usual causes. A cracked cap or a damaged sealing face calls for this part. An intact cap with water weeping past the stem points at the O-rings inside the valve, which are ordered separately, so look closely before deciding.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eKeeps the valve, not the whole assembly\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBecause the cap is available on its own, a damaged cap does not mean cutting a backwash valve out of the plumbing. The valve body and the connections stay exactly where they are.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48625745821908,"sku":"PAC-061-7731","price":50.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_68ba3e35-5aac-4681-ab72-f5c4d8cf22a3.jpg?v=1788690824"},{"product_id":"valve-spring","title":"Hayward Valve Spring","description":"\u003cp\u003eHayward SPX0603S is the valve spring for Hayward multiport valves. It is a new OEM part, not an aftermarket copy.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich valve it belongs to\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe part description names the Hayward SP0714T. The same spring is also carried under several other Hayward valve parts groups: the 1-1\/2 in. Vari-Flo top mount valves SP0710X, SP0711 and SP0712, the 2 in. Vari-Flo side mount valves SP0715 and SP0716, the SP0704 top mount four position valve, and the SP0740 DE 2 in. Selecta-Flo valve. Match SPX0603S against your own valve before ordering, because the sources differ on how widely it applies.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSold on its own\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis listing is the spring alone. The nylon spring washer set is a separate Hayward part, and it is worth looking at those washers at the same time since they sit with the spring and wear alongside it.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48625746411732,"sku":"HAY-061-2092","price":19.59,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6732085e-f0e8-4279-a26f-ad842d6d2c86.png?v=1788690916"},{"product_id":"pentair-270514z-fullfloxf-backwash-valve-rebuild-kit","title":"Pentair FullFloXF Backwash Valve Rebuild Kit","description":"\u003cp\u003ePentair 270514Z is the rebuild kit for the FullFloXF backwash valve. It is the genuine Pentair part, matched to that valve rather than a universal seal assortment.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRebuild rather than replace\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA backwash valve that no longer seals cleanly does not usually need a whole new assembly. The wear is in the parts this kit covers, and refreshing them puts the valve back into service for a fraction of the cost of replacing it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck the hard parts too\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWhile the valve is open, look at the diverters and the end cap. Pentair lists the center, inlet and outlet diverters and the end cap under their own part numbers, so a cracked or badly worn one can be ordered alongside this kit. Have o-ring lubricant ready for reassembly; it is not included here.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48625746444500,"sku":"PAC-061-7742","price":151.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_89311671-dd31-4fb3-92a5-46aa9c3de22f.jpg?v=1788690920"},{"product_id":"clamp-assembly-6-1-2-plastic","title":"Pentair Genuine OEM Six-Way HiFlow Valve Clamp with Screw and Nut","description":"\u003cp\u003eThe Pentair 152165 is the plastic clamp assembly for the six-way 1-1\/2 in. HiFlow multiport valve, and it ships with the screw and the nut. It is the genuine Pentair part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe clamp is what holds the multiport valve down on the filter tank. Drawn up on its screw and nut, it keeps the joint together against system pressure. When the clamp cracks or the hardware corrodes away, the valve starts to lift and weep at the seam, and the filter loses pressure.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich systems\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003ePentair lists it for the six-way 1-1\/2 in. HiFlow valve and for Sand Dollar and Meteor filter systems, on filters built before April 2004.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSize\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe listing describes it two ways, as a 6-1\/2 in. plastic clamp and as having a 6 in. inside diameter. Both figures are carried here rather than picking one, so measure the clamp on your filter before ordering.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48625747034324,"sku":"PAC-051-1644","price":31.94,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_2398a204-8754-4300-bdcc-89d2bd6dd266.png?v=1788691324"},{"product_id":"cover-o-ring-3-id","title":"Jandy Cover O-Ring, 3 in. ID","description":"\u003cp\u003eThe Jandy 1132 is the cover o-ring for Jandy valves, 3 in. inside diameter with a 3\/32 in. thick cross section. It is the genuine Jandy part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it seals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAn o-ring is a simple round gasket that squeezes between two surfaces. This one sits between the valve cover and the valve body. When it is fresh it takes up the gap and holds pressure. As it ages it hardens, flattens into an oval and loses the springiness that makes the seal work, and the valve starts to weep at the cover.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eMeasure the old ring across the inside opening. This part is the 3 in. inside diameter size. A ring that has taken a set will read slightly larger and thinner than the new figures, so compare it against a known good ring if you have one.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48625757192404,"sku":"JDY-201-2255","price":16.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_212eb97e-fff8-44d8-b950-f9fbfa2219cd.jpg?v=1788691966"},{"product_id":"controller","title":"Caretaker Controller Kit for UltraFlex 2 Valve","description":"\u003cp\u003eThe Caretaker 4-7-320 is the controller kit for the UltraFlex 2 valve. It is the genuine Caretaker part, supplied as a kit rather than a loose circuit board.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the UltraFlex 2 valve does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe UltraFlex 2 is an electric 8 port valve, the only one of its kind on the market. Eight ports and electric actuation are what let it move a large volume of cleaning water through a pool, which is why it turns up on bigger pools and on pools that also have to feed several water features.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace the controller\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe controller is the part that decides when the valve steps from one port to the next. When it fails, the valve stalls or skips, and the symptom on the pool side is uneven cleaning: some zones run all the time while others go dry. Fitting the factory kit puts the sequencing back the way it was designed.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48625785864404,"sku":"CTK-20-8700","price":415.52,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_1677efe3-b8c7-4411-9340-0063065a2dc0.png?v=1788692445"},{"product_id":"pentair-274417z-waste-valve-seal-for-fullflo-xf-backwash-valve","title":"Pentair FullFloXF Backwash Valve Waste Seal","description":"\u003cp\u003eThe Pentair 274417Z is the waste valve seal for the FullFloXF backwash valve. It is the genuine Pentair part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the waste seal does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA backwash valve has to hold the waste port shut every minute it is not backwashing. That job belongs to this seal. When it hardens, takes a set or nicks, the port stops closing completely and a steady trickle leaves the waste line while the system is supposed to be filtering. On a pool that is topped up automatically, that leak can run for weeks before anyone notices the water bill.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis listing is the seal on its own. The waste seal spring is a separate Pentair part, and so are the inlet and outlet diverters. If the valve is already open and it has some age on it, look at all of them while you are in there rather than doing the job twice.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48625785962708,"sku":"PAC-051-1652","price":57.31,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_23c68f55-07de-45ea-bd90-8a8939494d21.jpg?v=1788692456"},{"product_id":"seal-for-diverter-hi-flo-valve-2","title":"Pentair Seal for Diverter, Hi-Flo Valve 2\"","description":"\u003cp\u003eThe Pentair 272409 is the diverter seal for the 2 in. Hi-Flo side mount valve. It is catalogued under the Hi-Flo 2 in. valves 261049, 261050 and 261142.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA diverter valve works by swinging a body across the ports inside the valve. The body is what moves, but the seal is what closes. It presses against the port face and blocks it. When that rubber hardens with age, flattens under its own load or tears, the diverter still swings but no longer shuts anything off, and water bypasses to the port that should be closed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eService notes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe seal sits on the diverter under the valve cover, so it is renewed by opening the valve rather than by cutting anything out. If the diverter itself is scored or cracked, that is a separate part.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48626099650772,"sku":"PAC-061-3004","price":27.37,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_24598b44-51cb-44f3-90f0-b8b308bce93f.jpg?v=1788704713"},{"product_id":"diverter-2-2-3-way-compool-diverter-valves","title":"Pentair Diverter, 2\" 2\/3 Way Compool Diverter Valves","description":"\u003cp\u003eThe Pentair 270056 is the replacement diverter assembly for Compool diverter valves. It is the genuine Pentair part and serves both 2 way and 3 way valve bodies.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the diverter is\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eInside a diverter valve, the diverter is the piece that swings on the stem and covers a port. Everything else in the valve body is static. That makes the diverter the part that wears, and on a valve turned daily, it is the reason a valve starts letting water past a port it is supposed to close.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSizing\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis part is listed as the 2 in. diverter, and the product description covers 2 in. and 2.5 in. diverter valves. Both readings are carried here rather than picking one. If your valve is the larger size, measure the body and compare it against the old diverter before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe valve cover comes off, the old diverter lifts out and the new one drops in. There is no cutting and the plumbing is not disturbed.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48626100666580,"sku":"COM-561-1778","price":73.65,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_afcbd08f-0dcb-4502-986e-b64fe0061d46.png?v=1788704731"},{"product_id":"plug-gasket-assembly","title":"Sta-Rite Plug and Gasket Assembly for 1-1\/2\" MultiPort Valve","description":"\u003cp\u003ePart 14965-0028 is the plug and gasket assembly for the 1-1\/2 in. Sta-Rite MultiPort valve. It is catalogued under the Sta-Rite top mount 1-1\/2 in. Cristal-Flo and Waterford WC112-148 valve parts. The listing brand is Sta-Rite, and the part is also described as a genuine Pentair product under the same number; both names are carried here.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePlug and gasket as one\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe plug threads into the valve body and the gasket is what actually seals it. They are supplied together because the gasket is almost always the failure and there is no sense fitting a fresh one to a plug whose threads have already been strained.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe usual failure\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe gasket takes a set, hardens and stops sealing, and the valve weeps at the plug. The instinct is to tighten it, which puts all the load on the plastic threads and splits the plug. Once that happens both pieces need replacing, which is what this assembly is.\u003c\/p\u003e","brand":"Sta-Rite","offers":[{"title":"Default Title","offer_id":48626101747924,"sku":"STA-061-5822","price":61.76,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_56c3ed39-2f6b-4b9a-9818-e396acd67b53.png?v=1788704739"},{"product_id":"pentair-150119-union-replacement-kit-for-1-1-2-inch-hiflow-valves","title":"Pentair 1.5\" Black 3 Piece Union Kit for HiFlow Valves","description":"\u003cp\u003eThe Pentair 150119Z is the three piece union replacement kit for 1-1\/2 inch HiFlow valves, in black. It is the genuine Pentair kit and is carried under the number 150119 as well.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy unions fail first\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA union is the joint that lets a valve come out of the line without cutting pipe, and it is also the first place a valve starts to weep. Sun, chemistry and years of being tightened by hand take the o-ring out of shape and stress the nut. The valve body itself is usually fine long after the union has stopped sealing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat you get\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe kit covers the three piece union set for the 1-1\/2 inch valve. It is the black version, which matches the black valve bodies at most equipment pads. The 2 inch valve uses a different kit, so check the size stamped on the valve before you order.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48626106138836,"sku":"PAC-061-3216","price":75.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_05226bac-7002-46e9-b183-a2150b4b67c7.jpg?v=1788704866"},{"product_id":"shaft-replacement-kit","title":"Jandy Shaft Replacement Kit for Push Pull Valves","description":"\u003cp\u003eThe Jandy R0442200 is the shaft replacement kit for the push pull slide valves SVLV8, SVLV2 and BWVL-SLD. It is the genuine Jandy part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the kit covers\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is a full shaft assembly rather than a single o-ring: shaft, handle, handle pin, shaft pin, index plate lid, lid union nut, lid o-ring, shaft top o-ring and the purple shaft bottom o-ring. Between them they cover the parts that actually fail on a push pull valve.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen you need it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe two common complaints are a valve that weeps around the shaft, and a handle that has gone stiff or has broken its pin. Both come back to the shaft and its o-rings. Renewing the shaft and all three seals in one go is more reliable than chasing a single ring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe kit works from the top of the valve. The valve body stays in the plumbing, so the repair does not mean cutting pipe.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48626123964628,"sku":"TLD-061-4422","price":47.61,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6af709bd-f001-4751-8a54-553a1b07377f.jpg?v=1788705175"},{"product_id":"pentair-270200z-inlet-diverter-for-fullfloxf-backwash-valve","title":"Pentair Inlet Diverter for FullFloXF Backwash Valve","description":"\u003cp\u003eThe Pentair 270200Z is the inlet diverter for the FullFloXF backwash valve. It is the genuine Pentair replacement for the internal diverter on the inlet side of the valve.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the diverter does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eInside a push pull backwash valve, the diverter is the part that decides where water goes. Move the handle and the diverter changes the path, sending flow through the filter in one position and out to waste in the other. Everything the valve does depends on that seal being tight.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe symptom\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWhen a diverter wears, water starts to slip past instead of being redirected. The valve backwashes weakly, or some flow goes to waste while the system is meant to be filtering. Replacing the diverter restores the separation between the two paths.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhile the valve is open\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis listing is the inlet diverter only. The outlet diverter, the end cap and the valve O-rings are separate Pentair items, and it is worth looking at all of them once the valve is apart.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48626208866516,"sku":"PAC-061-7738","price":67.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/pentair_inletdiverter.jpg?v=1788706049"},{"product_id":"psv-valve-upper-kit","title":"Hayward PSV Valve Upper Kit","description":"\u003cp\u003eThe Hayward PSXVBCA is the upper kit for Hayward PSV series plumbing valves, sold as a rebuild and overhaul kit. It is a new OEM Hayward part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRebuild rather than replace\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA diverter valve is glued into the plumbing, so replacing one means cutting pipe, fitting couplings and waiting on cure time before the system can run again. The upper kit avoids all of that. It covers the top section of the valve, which is where PSV valves actually wear out, and the body stays exactly where it is.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat goes wrong\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003ePSV valves normally fail in one of two ways: water starts weeping around the cover or the handle shaft, or the diverter stops sealing cleanly so water bypasses to the port that is supposed to be shut. Both are upper section problems, and both are what this kit is for.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626210996436,"sku":"HAY-561-1001","price":93.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_71041f85-7080-46ee-9fe9-a99e6e9f5845.jpg?v=1788706154"},{"product_id":"valve-shaft-o-ring","title":"Jandy Valve Shaft O-Ring R0487100, O-158","description":"\u003cp\u003eJandy R0487100 is the O-ring that seals the valve shaft, listed under the O-ring size O-158. It measures 15\/16 in. across the outside, 3\/4 in. across the inside, and 3\/32 in. thick.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe leak it fixes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWater appearing around the valve handle almost always means the shaft O-ring has hardened, flattened or torn. The valve body itself is rarely the problem. Swapping this one seal is what puts the valve right, and it takes a few minutes with the pump off and the system drained down.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eConfirm the dimensions against the ring you remove. If the old seal has gone brittle it may come out in pieces, so measure the groove rather than the fragments.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48626491097300,"sku":"JDY-561-7100","price":2.61,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_6c8f8422-92fb-4a03-815c-926b7c5e9a92.jpg?v=1788710886"},{"product_id":"valve-key-assembly","title":"Hayward Valve Key Assembly","description":"\u003cp\u003eThe Hayward PSXVDE is the replacement valve key assembly for Hayward PSV series valves. It is a new genuine Hayward part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat the key does\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eInside a diverter valve, the body is fixed and the key is the piece that moves. The handle turns the key, and the key seals against the seat to open one port and close another. Everything the valve is asked to do depends on that seal.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eTwo symptoms point at the key. One is flow going where it should not, water still reaching a closed port because the key no longer seals. The other is a handle that has gone stiff or notchy. Both are cheaper to fix with a key assembly than by replacing the whole valve.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48626496405716,"sku":"HAY-561-1003","price":42.66,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_a79bf0ff-2aaa-4157-8c99-9412d82d66f3.jpg?v=1788710949"},{"product_id":"water-valve-top-dome-black","title":"Paramount Water Valve Top Dome, Black","description":"\u003cp\u003eThe Paramount 005-302-4300-03 is the top dome for the Paramount water valve, in black. It is the genuine Paramount part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis listing covers the dome alone, the piece that caps the top of the water valve body. The valve itself is not included, so it suits a repair where the dome has cracked, faded from years in the sun, or been damaged while the valve was being serviced.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eGetting the right one\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eParamount lists its domes by part number and color. Read the number off the old dome or from the valve documentation and match it to 005-302-4300-03 before ordering, since a dome that looks the same can belong to a different valve.\u003c\/p\u003e","brand":"Paramount","offers":[{"title":"Default Title","offer_id":48626564301012,"sku":"PMT-201-600","price":165.54,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b8709dca-8e68-401e-9822-05591d037441.jpg?v=1788712518"},{"product_id":"5-spoke-spider-gasket-6-od","title":"Pentair American Products 5 Spoke Spider Gasket, 6\" OD","description":"\u003cp\u003eThe Pentair 51008400 is the five spoke spider gasket for Pentair American Products 1-1\/2 inch side mount multiport valves, models 501501 and 501601. It measures 6 inches on the outside and 1 inch on the inside, and it is the pattern used on valves built after 1976.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCount the spokes before you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eAmerican Products used more than one spider gasket pattern over the years, and they are not interchangeable. Take the old one out and count the spokes. Five spokes means this part. Check the outside diameter too, since 6 inches is what confirms it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy they fail\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe spider gasket is what keeps each port of a multiport valve separate from its neighbors. As the rubber compresses and hardens, water starts crossing between ports inside the valve. The classic symptoms are a trickle out of the waste line while the valve is set to filter, or a backwash that never seems to finish clearing. Both are the gasket, not the filter.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eClean the gasket channel in the valve body out completely before seating the new gasket, and press it in evenly all the way around. A silicone sealant or lubricant helps it bed in and stay put while the valve goes back together.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48626567577812,"sku":"AMP-061-1076","price":32.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c1d4aa30-c3d8-4da6-b777-fbed529f397c.gif?v=1788712531"},{"product_id":"o-ring-kit-for-2-in-1","title":"Jandy O-Ring Kit for 2-in-1 Backwash Valve","description":"\u003cp\u003eJandy R0552400 is the o-ring kit for the Never Lube 2-in-1 backwash valve. It covers the BWVL-NVL, 8034J and 8034 valves, and it is the genuine Jandy part rather than an assortment of generic rings.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the o-rings are the wear item\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe Never Lube design is meant to be serviced without grease, so the seals carry the whole sealing job on their own. Over seasons of pressure cycles, chlorine and heat, they harden and take a set. That is when a valve that has been fine for years starts weeping around the body or the diverter shaft.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eKit, not singles\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBuying the kit means the matched set arrives together. Replacing one o-ring and leaving the rest in place tends to move the leak rather than end it, so doing them all while the valve is open is the sensible approach.\u003c\/p\u003e\u003cp\u003eThe diverter itself is a separate Jandy part. If the valve is not sealing between positions after new o-rings, that is where to look next.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48626582487252,"sku":"TLD-061-5524","price":23.62,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_1a2acc71-0a5d-4e37-886c-595db147faa4.png?v=1788712697"},{"product_id":"piston-rod-assembly-for-slide-valve","title":"Pentair Piston Rod Assembly for Slide Valve","description":"\u003cp\u003eThe Pentair 273241Z is the piston rod assembly for the 2 inch PVC push pull slide valve, the Pentair and Pac-Fab 26-1165. It is the genuine OEM assembly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIdentifying the right one\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe measurement that matters is the centerline, and this assembly is 7-1\/2 inches. The shaft also carries Piston Assembly 27-3241 molded into it, which is the quickest way to confirm a match against the part already in the valve. The listing is sold as 273241Z and the source material also shows the number as 273241; both point at this same assembly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy it wears\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe piston rod is the moving part of a push pull valve, stroking up and down every time the valve is operated. Over years the shaft scores and the seals ride on a rougher surface, and the valve gets stiff or starts passing water when it should be closed. Replacing the rod assembly is the usual fix.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48626598346964,"sku":"PAC-061-2755","price":101.76,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_63145092-54a3-4570-92c9-74984fc25245.png?v=1788712911"},{"product_id":"2-valve-spider-gasket","title":"Sta-Rite 2\" Valve Spider Gasket for MultiPort Valve","description":"\u003cp\u003eSta-Rite 14971-SM20E12 is the spider gasket for 2 in. multiport valves. It has five spokes and a 6-5\/8 in. outside diameter, and it is the part that seals one port from the next inside the valve body.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it fixes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe spider gasket takes the whole load every time the handle moves, and it flattens and hardens with age. When it goes, the valve stops respecting the position it is set to: water runs to waste with the handle on filter, or unfiltered water finds its way back to the pool. Nothing else in the valve produces that symptom the same way.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eGetting the size right\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the 2 in. gasket. The 1-1\/2 in. valve takes a smaller gasket with a different spoke pattern, so lay the old one next to the measurement above before you order. It is listed as a service part for the Sta-Rite 2 in. Cristal-Flo top mount valve and for the Sta-Rite 1-1\/2 in. and 2 in. side mount multiports.\u003c\/p\u003e","brand":"Sta-Rite","offers":[{"title":"Default Title","offer_id":48626731647188,"sku":"STA-061-9680","price":52.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_0f060be3-1144-4e0a-b347-0c0090422ea8.jpg?v=1788714156"},{"product_id":"union-adapter-kit-2-1-2-x-2","title":"Pentair Union Adapter Kit 2-1\/2\" x 2\"","description":"\u003cp\u003ePentair 274426Z is the union adapter kit in 2-1\/2 in. by 2 in., used on the Clean and Clear Plus filter and the FullFloXF backwash valve. It is the genuine Pentair part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is for\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe kit takes the larger 2-1\/2 in. port and adapts it to 2 in. plumbing, at a union so the connection can be broken later. That last part is the whole point of a union at an equipment pad: it is what lets a filter or a valve come off for service without a saw and a pile of new fittings.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to replace one\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eUnion nuts crack when they are over tightened, threads strip, and the sealing face gets scored by grit. Once any of that has happened the joint weeps no matter how hard it is cranked down, and the joint should be replaced rather than tightened further. Fitting a new kit is the reliable end to a persistent drip at the filter.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48626734629076,"sku":"PAC-061-2002","price":53.31,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/PAC-061-2002_2a.png?v=1788714212"},{"product_id":"6-flange-kit","title":"Fluidra USA 6\" Flange Kit for Butterfly Valves, 02376U","description":"\u003cp\u003eFluidra USA 02376U is the flange kit for 6 inch butterfly valves. It is the factory part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy a butterfly valve needs one\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSmall pool valves glue straight into pipe. A butterfly valve does not: the body is clamped between a pair of flanges, and those flanges are what carry it into the line. The flange kit is therefore not an accessory, it is how the valve gets installed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSizing\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the 6 in. kit, so it belongs on a 6 in. valve in a 6 in. line. That is large pipe, common on commercial pools and on big residential systems. Confirm the size of your valve body before ordering, since flange kits are not interchangeable across sizes.\u003c\/p\u003e","brand":"Astral","offers":[{"title":"Default Title","offer_id":48626824577236,"sku":"ASP-56-4123","price":321.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_980ddbd9-e51f-440f-b9b8-73792a0b7d69.png?v=1788715513"},{"product_id":"2-way-3-way-neverlube-valve-knob","title":"Jandy 2-Way\/3-Way NeverLube Valve Knob","description":"\u003cp\u003eThe Jandy R0486900 is the replacement knob kit for 2-way and 3-way NeverLube valves. It is the genuine Jandy Pro Series part, made by Zodiac Pool Systems, in black.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the knob goes first\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe valve body itself tends to outlast the handle. Years of sun and of being cranked round by hand crack the knob or wear the grip smooth, and eventually it splits or disappears. The valve is still good at that point, so replacing the knob is the whole repair.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe knob sits on the outside of the valve, so putting a new one on does not mean opening the water side of the valve body or cutting into the plumbing at the pad.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48626830934228,"sku":"JDY-561-1349","price":24.12,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_4130f66b-cd9b-4ee2-be64-e069286cacf1.jpg?v=1788715674"},{"product_id":"o-ring-valve-top-2","title":"Pentair Genuine OEM O-Ring, Valve Top, 2\"","description":"\u003cp\u003eThe Pentair 271151 is the genuine top valve o-ring for HiFlow 2 inch multiport valves, in both the top mount and side mount configurations. It measures 6-3\/4 inches inside diameter with a 1\/8 inch cross section.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it seals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe multiport valve is a body with a rotating diverter under a bolted cover. This o-ring goes between the body and that cover. It is the seal that keeps the whole valve from weeping around its rim once the bolts are torqued down.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eReading the leak\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWhere water shows up tells you which seal has failed. Dripping from the joint around the top cover is this o-ring. Water running continuously to waste while the valve is set to filter is the spider gasket underneath, a different part. Get that distinction right before you order.\u003c\/p\u003e\u003cp\u003eWhen the valve is open for any reason, replace this o-ring while you are in there. Lubricate it with a silicone pool lubricant, never a petroleum grease.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48626864849108,"sku":"PAC-051-2996","price":13.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_67bb2493-9253-4471-ac85-aa834ec1617a.png?v=1788716021"},{"product_id":"neverlube-diverter-kit","title":"Jandy NeverLube Diverter Kit","description":"\u003cp\u003eThe Jandy 4720 is the genuine NeverLube diverter kit. It covers NeverLube valves in the 1.5\" to 2\" and the 2\" to 2.5\" sizes, and it is the part to order when the valve body is fine but the switching is not.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the diverter goes first\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eInside every NeverLube valve, the diverter is the piece that swings across the ports and seals off the one you want closed. It is the only part that moves against a seal every time the handle turns, so it is the part that gives up first. The body itself, glued into the plumbing, usually outlives several diverters.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat replacing it fixes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWater bleeding through to a port that should be shut, a handle that turns without changing much, suction split between two lines that should be isolated. All of those point at the diverter rather than the valve.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48626965872852,"sku":"JDY-561-7685","price":86.61,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_9b18ebe3-e934-4915-92b2-c3c4572160ed.jpg?v=1788718579"},{"product_id":"gasket-valve-seat","title":"SuperPro Generic Gasket for Valve Seat SPX0740D","description":"\u003cp\u003eThe SuperPro G-418-9 is a generic valve seat gasket built to replace the Hayward SPX0740D. It is the part commonly called a spider gasket, and it is the seal that sits at the valve seat.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eGeneric versus OEM\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is a SuperPro made equivalent rather than a Hayward branded gasket. The Hayward number appears here so you can cross reference it against a diagram or a parts list. If your quote or work order calls for SPX0740D, G-418-9 is the SuperPro line item that answers it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to change it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eSeat gaskets are rubber, and rubber hardens, flattens and eventually splits. A gasket that has taken a set no longer seals cleanly against the seat, and the usual result is water passing where it should be shut off. It is worth fitting a fresh one any time the valve is opened up, because the gasket costs very little next to the valve it protects.\u003c\/p\u003e","brand":"Aladdin","offers":[{"title":"Default Title","offer_id":48626989662420,"sku":"SPG-601-1048","price":12.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_ce2c3520-a3cc-4a2c-a728-25ce76f30648.jpg?v=1788718794"},{"product_id":"check-valve-flap-kit","title":"Pentair Check Valve Flap Kit","description":"\u003cp\u003ePentair 263042Z is the check valve flap kit. It is also listed by Pentair as the replacement check valve diverter kit for 2 way and 3 way valves, and both descriptions refer to this same part number.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it fixes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA check valve exists to let water go one way and stop it coming back. The flap is the moving piece that does the stopping, and it takes a hit every time the pump starts and stops. When it tears, stiffens or stops seating, water runs backward when the system shuts down and the pump can lose prime.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRepair over replacement\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA flap kit lets the valve body stay glued in the plumbing. That turns what would be a cutting and repiping job into an internal parts change, which is why it is worth keeping the part number to hand.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48627345588436,"sku":"PAC-561-1001","price":41.03,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_90856e23-4cb5-4471-8e21-fbd5c70fc892.jpg?v=1788722716"},{"product_id":"valve-spring-washer","title":"Pentair 1\" White Valve Spring Washer","description":"\u003cp\u003eThe Pentair 271160 is the white valve spring washer used in the multiport valve stem assembly. It measures 1-5\/8 inches outside diameter, 1-1\/4 inches inside diameter and 3\/32 of an inch thick.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere it sits\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA multiport valve seals because a spring holds the rotor down against the seat. The washer is part of that stack, spreading the spring load so the stem assembly stays square. When it is missing, cracked or has been replaced with something close but not right, the rotor no longer seats evenly and water crosses between ports, which is the classic symptom of sand or DE returning to the pool.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCheck the size before ordering\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe product name refers to a 1 inch valve spring washer, and the part detail lists it for the HiFlow 2 inch top mount and side mount multiport valve. Both readings are carried here, so measure your old washer against the dimensions above rather than going by valve size alone.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRebuild the stack together\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe spring, the stem o-ring and the valve top o-ring wear on the same schedule as this washer. They are separate parts, and doing them at once means opening the valve once.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48627569557716,"sku":"PAC-061-2416","price":14.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b9502279-8d1d-4f6a-af73-e564b08d1dad.jpg?v=1788723742"},{"product_id":"cover-with-flapper-o-ring-large-check-valve-7307","title":"Jandy Cover with Flapper and O-Ring, Large Check Valve 7307","description":"\u003cp\u003eThe Jandy R0466000 is the cover, flapper and o-ring set for the 7307 large check valve, the body with 2.5 and 3 inch ports.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat fails on a check valve\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe valve body outlasts everything inside it. What wears is the flapper, the hinged plate that swings open with flow and drops shut to stop water running backwards. Over time it goes stiff, tears at the hinge or stops seating cleanly, and the line starts draining back when the pump shuts off.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eA top down repair\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBecause the failure is inside the lid, the fix does not involve cutting pipe. The cover comes off, the flapper is replaced and the new o-ring seals the cover on the way back. The valve body stays glued into the plumbing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMatch the valve first\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis set is for the 7307, the large body valve. Jandy makes smaller check valves that take their own parts, so confirm which one is in your line before ordering.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48627590987988,"sku":"JDY-561-2324","price":97.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_8c791798-476d-4de2-baf6-9f8e47dcf373.jpg?v=1788723997"},{"product_id":"2-way-3-way-neverlube-valve-handle","title":"Jandy 2-Way\/3-Way Neverlube Valve Handle","description":"\u003cp\u003eThe Jandy R0487200 is the genuine replacement handle for 2-way and 3-way Neverlube valves. One part covers both valve types.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy the handle is the part that fails\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eEverything you do to a diverter valve happens through the handle, and it is the weakest link in the assembly by design. Over time the internals stiffen, someone applies more force, and the handle either cracks at the hub or rounds out where it grips the stem. The valve underneath is usually fine. What is gone is your ability to move it and to know where it is set.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis is the handle on its own. The Neverlube valve knob and the valve shaft o-ring are separate parts, so add them if yours are damaged as well.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you refit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe handle sits on the valve cover and comes off without opening the plumbing. If the new handle takes real force to turn once fitted, stop and service the valve. Forcing a stiff valve is what broke the last handle and it will break this one too.\u003c\/p\u003e","brand":"Zodiac","offers":[{"title":"Default Title","offer_id":48627597279444,"sku":"JDY-561-7200","price":35.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_fcab523f-0299-4cb1-ade9-d7167d4db405.jpg?v=1788724056"},{"product_id":"rotor-shaft-o-ring","title":"Purex (Pentair) Rotor Shaft O-Ring","description":"\u003cp\u003eThe Purex JV18 is the rotor shaft O-ring for the Pentair SM and SMBW 2000 series backwash valves. Purex is now part of Pentair, and the part number carried over unchanged.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it seals\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIt sits around the rotor shaft inside the valve. Like any O-ring in a moving joint, it hardens and takes a set with age and chemical exposure, and when it does the valve starts to weep at the shaft under pressure.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBefore you order\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA backwash valve carries several O-rings of broadly similar size, so check yours against the parts diagram for the valve rather than by eye. If the valve is coming apart anyway, the rest of the seals in it are the same age and cost the same labor, and doing them together saves opening the valve twice.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48627601735892,"sku":"PUR-061-3407","price":3.97,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_b8d978f7-bf00-4877-bab3-288f04968065.jpg?v=1788724092"},{"product_id":"valve-diverter","title":"Jandy Never Lube Large Valve Diverter","description":"\u003cp\u003eJandy R0465800 is the large valve diverter for the Never Lube valve, listed for models 4718 and 4719. It is a new OEM Jandy part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it is\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe diverter is the moving piece inside the valve. When you turn the handle, it is the diverter that swings across and sends water to one port instead of another. Everything else in the valve body exists to hold it in position and seal around its edges, which is why a worn diverter shows up as flow reaching a port that is supposed to be shut.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhen to change it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe usual complaint is a valve that no longer fully closes off a leg. Turn the handle to its stop and water still moves where it should not, or two circuits both get partial flow when only one should. Once the valve top is off, swapping the diverter is quick, so check the seal and the handle at the same visit rather than opening the valve twice.\u003c\/p\u003e","brand":"Jandy","offers":[{"title":"Default Title","offer_id":48627603374292,"sku":"JDY-561-1301","price":134.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_c14fa16a-cc91-44c4-927f-fcfabb800d1d.jpg?v=1788724122"},{"product_id":"stem-o-ring","title":"Pentair Stem O-Ring for 2\" Multiport Valves","description":"\u003cp\u003eThe Pentair 271162Z is the stem O-ring for 2 in. top mount and side mount multiport valves. It seals around the stem, the shaft that the handle turns to select filter, backwash, rinse and the rest of the positions.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe leak it fixes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eWhen a multiport starts weeping around the handle, the stem O-ring is the reason nearly every time. The O-ring hardens, flattens or gets scored by grit that has worked its way in, and water finds a path up the shaft. It is a small part failing in an obvious place, and replacing it is far quicker than chasing the valve body.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhile the valve is apart\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eGetting to the stem means the handle assembly comes off, so it is worth having the valve spring, the spring washer and the handle washer on hand. They are sold separately and are the other pieces that wear in that stack. Note that the parts diagrams this O-ring appears in cover both 2 in. and 1-1\/2 in. multiport valves, so confirm the valve size before ordering.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48627713081556,"sku":"PAC-061-2418","price":5.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_8ed37f19-336f-41c4-8caf-8d7e667f7fd4.jpg?v=1788727029"},{"product_id":"piston-assembly-o-ring","title":"Pentair Piston Assembly O-Ring","description":"\u003cp\u003eThe Pentair 35505-1318 is the piston assembly O-ring for the Sta-Rite WC212-134 push pull valve. It has a 2-1\/2 inch inside diameter and may also fit other Sta-Rite valves.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it fixes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA push pull valve seals by sliding a piston through a bore, and it is the O-rings on that piston that make the seal. When one hardens, flattens or picks up a nick, water bypasses the piston, and the symptom is a valve that no longer isolates properly in one or both positions.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitting it\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eMeasure the inside diameter of the old ring against the 2-1\/2 inch figure to confirm the match. A silicone based O-ring lubricant on assembly helps the ring seat cleanly and stops it tearing as the piston goes home.\u003c\/p\u003e","brand":"Sta-Rite","offers":[{"title":"Default Title","offer_id":48627752796372,"sku":"SWQ-061-3959","price":15.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_1b54f6b1-204c-4b76-a576-0b92a0faf303.jpg?v=1788727730"},{"product_id":"key-cover-o-ring-kit","title":"Hayward PSV Series Key Cover O-Ring Kit","description":"\u003cp\u003eThis is the Hayward key cover o-ring kit, part number PSXVZ2A, designed to fit Hayward PSV model valves. It is a new OEM Hayward part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat it addresses\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA diverter valve is sealed at the cover that holds the key down. Those o-rings spend their life compressed, warm and in treated water, and over a few seasons they harden and take a permanent set. The result is a slow weep at the top of the valve that gets worse every time somebody turns the handle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWorth doing first\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA seal kit is a small part of the cost of a replacement valve and does not disturb the plumbing. Unless the body itself is cracked or the key is scored, reseal the valve before you cut anything out.\u003c\/p\u003e","brand":"Hayward","offers":[{"title":"Default Title","offer_id":48627762856148,"sku":"HAY-561-1005","price":17.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_5987cf17-6737-4f39-a521-dbb40ba8d0a8.jpg?v=1788727838"},{"product_id":"union-kit","title":"Pentair Genuine OEM Union Kit for 2\" Top Mount MultiPort Valve","description":"\u003cp\u003eThe Pentair 272590Z is the union kit for the 2\" 6-position top mount clamp-on multiport valve. It is the genuine Pentair part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy unions\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eA multiport valve is one of the parts most likely to need attention over the life of a filter, whether that is a worn spider gasket, a seized handle or a full replacement. If the valve is glued straight into rigid pipe, every one of those jobs starts with a saw. Unions turn it into a job you can do by hand.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFitment\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis kit is matched to the 2\" 6-position top mount clamp-on valve. Check the size and the style of the valve you have, since the top mount clamp-on and the side mount valves take different connections.\u003c\/p\u003e","brand":"Pentair","offers":[{"title":"Default Title","offer_id":48627839664340,"sku":"PAC-051-3074","price":51.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_fd80d9fd-ba86-463d-abe7-d266335adc34.jpg?v=1788728062"},{"product_id":"stainless-steel-pentair-piston-rod-assebmly","title":"CMP Stainless Steel Piston Rod Assembly for Pentair Push Pull Valve","description":"\u003cp\u003eThis is the CMP stainless steel piston rod assembly for the Pentair 2 in. PVC push pull valve. It replaces the Pentair OEM 273241 assembly, with a stainless shaft in place of the original.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eChecking the fit\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe assembly measures 7-1\/2 in. centerline, and the shaft carries Piston Assembly 27-3241 molded into it. Measure the rod you are pulling out against that before you order, because push pull valves come in more than one size and the rod length is the thing that tells them apart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePart numbers\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe same assembly is listed under 273241SS, 273241HD, 25831-122-100 and 273241. If your paperwork or the valve label shows any of those, you are in the right place.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy it fails\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe piston rod takes the full push and pull of every backwash cycle, and the seals ride on it. Once the shaft is scored or bent, the piston will not seat cleanly and the valve leaks between ports no matter how good the seals are.\u003c\/p\u003e","brand":"CMP","offers":[{"title":"Default Title","offer_id":48627948912852,"sku":"CTM-051-3001","price":131.92,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/default_265ab8e3-3887-402b-bd39-b385c54294b0.jpg?v=1788730626"}],"url":"https:\/\/www.activepoolsupply.com\/collections\/valve-parts.oembed","provider":"Active Pool Supply","version":"1.0","type":"link"}