{"product_id":"igarden-p-series-variable-speed-inverter-pool-pump","title":"iGarden P Series Variable Speed Inverter Pool Pump, In Ground and Above Ground, 115V\/230V","description":"\u003cp\u003eThe iGarden P Series is a variable speed inverter pool pump for permanently installed in ground and above ground pools, built around an IE4 DC brushless motor and made in three sizes: P08, P11 and P15. All three run on 115V or 230V, carry a full touchscreen on the motor end, connect to the iGarden app over Wi-Fi, and come with two 2 in. unions in the box.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThree sizes\u003c\/strong\u003e\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eiGarden rating\u003c\/th\u003e\n\u003cth\u003eTHP at 230V (115V)\u003c\/th\u003e\n\u003cth\u003eMaximum flow at 230V (115V)\u003c\/th\u003e\n\u003cth\u003eMaximum head\u003c\/th\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eP08\u003c\/td\u003e\n\u003ctd\u003e0.85 HP\u003c\/td\u003e\n\u003ctd\u003e0.85 THP (0.85 THP)\u003c\/td\u003e\n\u003ctd\u003e101 GPM (101 GPM)\u003c\/td\u003e\n\u003ctd\u003e56 ft\u003c\/td\u003e\n\u003ctd\u003eDB19DV\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eP11\u003c\/td\u003e\n\u003ctd\u003e1.25 HP\u003c\/td\u003e\n\u003ctd\u003e1.20 THP (1.05 THP)\u003c\/td\u003e\n\u003ctd\u003e118 GPM (110 GPM)\u003c\/td\u003e\n\u003ctd\u003e62 ft\u003c\/td\u003e\n\u003ctd\u003eDB23DV\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eP15\u003c\/td\u003e\n\u003ctd\u003e1.75 HP\u003c\/td\u003e\n\u003ctd\u003e1.65 THP (1.25 THP)\u003c\/td\u003e\n\u003ctd\u003e136 GPM (123 GPM)\u003c\/td\u003e\n\u003ctd\u003e67 ft\u003c\/td\u003e\n\u003ctd\u003eDB28DV\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eThe P08 gives the same output on either voltage. The P11 and P15 give their full output on 230V and a little less on 115V, which matters if the equipment pad only has 115V. Our \u003ca href=\"\/pages\/pool-pump-size-calculator\"\u003epool pump size calculator\u003c\/a\u003e works out the flow your pool needs from its volume and turnover.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe motor and the drive\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAn IE4 DC brushless motor on an inverter drive runs at the speed you set, from 30 to 100 percent in 5 percent steps, with a soft start. iGarden puts its energy use at over 10 times better than a single speed pump. Its own comparison runs a 1.5 HP single speed pump against the P11 for 16 hours a day on a 16,000 gallon pool at 20 cents per kWh and gets 8,760 kWh a year against 876. Your figure depends on your rate, your hours and how low a speed turns your pool over. iGarden rates the noise at 36 dBA.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eControls\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe touchscreen locks after a minute and unlocks with a three second press. From it you set the running speed, four daily timers (a start, an end and a speed for each), a one touch backwash at full speed, and a live power reading. Every start primes the pump on its own, counting down from 1,500 seconds until it senses water, and it then settles at 80 percent until you change it. The iGarden app adds the same controls, more timers, power statistics and sharing with the family on a 2.4 GHz Wi-Fi network. For automation, a seven pin connector gives four digital inputs (stop, 100, 80 and 40 percent) and RS485 Modbus.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIt is wired to a GFCI protected circuit with copper conductors; the pump accepts 115V or 230V and senses which. The manufacturer's rules: no more than 6.5 ft above the water level, at least 6 ft from the inside of the pool walls, 6 in. of air around the motor, indoors or in the shade, and bonded with 8 AWG copper. Plumb it with 2 in. pipe, keep any elbow at least 14 in. from the inlet, and use only the supplied unions on the pump body. Fill the strainer before the first start; it is not built to run dry. Salt pools up to 3.5 percent salt are fine. It is not for storable pools.\u003c\/p\u003e","brand":"iGarden","offers":[{"title":"P08 Model, 0.85 HP","offer_id":67906774597844,"sku":"PSU-209304","price":564.99,"currency_code":"USD","in_stock":false},{"title":"P11 Model, 1.25 HP","offer_id":67906813624532,"sku":"PSU-209306","price":660.99,"currency_code":"USD","in_stock":false},{"title":"P15 Model, 1.75 HP","offer_id":67906813722836,"sku":"PSU-209309","price":679.02,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0801\/9568\/2516\/files\/igarden-p-series-variable-speed-pool-pump.jpg?v=1792606196","url":"https:\/\/www.activepoolsupply.com\/products\/igarden-p-series-variable-speed-inverter-pool-pump","provider":"Active Pool Supply","version":"1.0","type":"link"}